background image

— 21 —

Correction

• Insert the cassette with the window side up and the record

tab facing you.

• Check that a cassette tape is not already inserted. Press

EJECT

 

0

.

• Check that the AC power cord is correctly connected to

an AC outlet.

• If the 

 (Timer) indicator is lit on the display, press

POWER

 to cancel timer recording, then press 

EJECT

0

.

• Check that the record tab on the back of the cassette is

not removed. (

P.14)

Miscellaneous

A cassette cannot be inserted.

The cassette does not eject.

The cassette ejects when you press 

REC/OTR 

, or when

you press 

POWER

 to set timer recording.

General

Mains voltage

AC 110 – 240V

Mains frequency

50/60Hz

Power consumption

Approx. 18 watts

Ambient temperature

+5°C to +40°C

Relative humidity

10% to 80%

Dimensions

Approx. 400(W) x 94(H) x 272(D) mm

Mass

Approx. 3.1kg

Position for use

Horizontal

Video output channel

UHF E36 (adjustable between E28 — E60)

Possible number of TV channel

99

Number of pre-programmable memory blocks

8

Number of days in advance

365 or every day, or every week

Tuner

Aerial input

B/G, D/K, I, SECAM K1

VHF L:

42 — 175 MHz

VHF H:

175 — 470 MHz

UHF:

470 — 870 MHz
CATV

Video

Input (VIDEO IN)

0.5 to 2.0 Vp-p, 75 ohms

Output (VIDEO OUT)

1.0±0.2 Vp-p, 75 ohms

Resolution

Better than 240 lines

Signal/noise ratio

Better than 43 dB

Audio

Input (AUDIO IN)

–8 dBs, 50k ohms (0dBs=0.775 Vrms)

Output (AUDIO OUT)

–6 dBs, 1k ohms (0dBs=0.775 Vrms)

Accessories supplied

Remote control unit
RF coaxial cable
Batteries – R6(SUM-3)/AA (only for checking operations)

S

PECIFICATIONS

Design and specifications are subject to change without notice.

VR288/488-55 EN (N)

5/31/99, 3:15 PM

21

Summary of Contents for VR288/55





















Reviews: