background image

 

I.

 

Introduction

 

- This monitor is color TFT LCD monitor, with compact and ecological design. 

- On Screen Display provide flexibility with simple & user-friendly controls. 
- USB interface Projected Capacitive Touch Panel and Resistive Touch (for touch model only) 

 

 

Features 

- 8 inch diagonal screen with native display resolution 800 * 600. 

- Full flat front panel with high quality touch panel or cover lens. 

- Fully Glossy surface throughout monitor’s appearance. 
- Rimless front bezel design, spill & dust proof. 

- Cable management down routing through the mounting stand. 

- Light weight. 
- Mitsubishi PMMA cover lens for P080VG. 

- 5 wires resistive touch screen panel for P080VR. 

- Projected Capacitive Touch panel for P080VP. 

 

 

Unpack the monitor 

- Put the monitor on a clean surface, make sure the box in upright position. 
- Remove packing materials from inside of box. 

 

 

Check accessory 

 

Please make sure the entire accessory is included: 

 
 

 

 
 

 

 
 

 

 

 

 

 

Power Adaptor, the plug 

type could be modified 

by order. 

 

 

 

1.8meter VGA 15 pin   

D-sub video cable 

 

USB cable for Touch 

control   

(For touch model only). 

Summary of Contents for P080VG


















Reviews: