background image

 

1

 

U

U

s

s

e

e

r

r

 

 

M

M

a

a

n

n

u

u

a

a

l

l

 

 

/

/

 

 

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

 

 

G

G

u

u

i

i

d

d

e

e

 

 

M

M

o

o

d

d

e

e

l

l

 

 

N

N

o

o

.

.

 

 

P

P

1

1

5

5

0

0

T

T

R

R

 

 

 

 

Warning!

      This monitor is equipped with Mini USB port, signals and power is obtained from standard 

USB 2.0 or USB 3.0 port. Do not expose this unit in the rain or moisture environment to damage the 
monitor.   

PRECAUTIONS 

 

Do not use the monitor near water. 

 

Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a 
person and cause serious damage to the appliance. Use only a cart or stand recommended by the 
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting 
kit approved by the manufacturer and follows the kit instructions. 

 

The monitor should be operated with an USB cable with Mini USB B type connector on monitor end 
and standard USB A type connector on the other end to PC or USB signal source.   
Normally it is packed with monitor. 

 

Never spill liquids on the monitor. 

 

Do not attempt to service the monitor yourself; opening or removing covers can damage to the 
monitor or panel. Please refer all servicing to qualified service personnel. 

 

For Wall mount adaptor, wall socket shall be installed near the equipment and shall be easily 
accessible. 

 

Summary of Contents for P150TR














Reviews: