Phoenix Contact 2981428 Manual Download

Page: 4 / 10

PSR-...-24DC/ESD/5X1/1X2/300

102104_en_03

PHOENIX CONTACT

Switching capacity (360/h cycles)

4 A (24 V DC)
4 A (230 V AC)

Switching capacity (3600/h cycles)

2.5 A (24 V (DC13))
3 A (230 V (AC15))

Output fuse

6 A fast blow (undelayed)
10 A gL/gG NEOZED (delayed)

Output data

General data

Relay type

Electromechanically forcibly guided, dust-proof relay.

Nominal operating mode

100% operating factor

Degree of protection

IP20

Min. degree of protection of inst. location

IP54

Mounting position

any

Mounting type

DIN rail mounting

Air clearances and creepage distances between the power circuits

DIN EN 50178/VDE 0160

Rated insulation voltage

250 V

Rated surge voltage/insulation

4 kV / basic isolation, (safe isolation, reinforced insulation and 6 kV between the
enabling current paths

(13/14, 23/24, 33/34)

and the remaining current paths

and between

13/14, 23/24, 33/34

between each other.)

Pollution degree

Surge voltage category

III

Dimensions

Screw connection

Spring-cage connection

W x H x D

45 x 99 x 114.5 mm

45 x 112 x 114.5 mm

Connection data

Screw connection

Spring-cage connection

Conductor cross section, solid

0.2 mm² ... 2.5 mm²

0.2 mm² ... 1.5 mm²

Conductor cross section, stranded

0.2 mm² ... 2.5 mm²

0.2 mm² ... 1.5 mm²

Conductor cross section AWG/kcmil

24 ... 12

24 ... 16

Stripping length

7 mm

8 mm

Ambient conditions

Ambient temperature (operation)

-20 °C ... 55 °C

Ambient temperature (storage/transport)

-40 °C ... 70 °C

Max. permissible relative humidity (operation)

75 % (on average, 85% infrequently, non-condensing)

Max. permissible humidity (storage/transport)

75 % (on average, 85% infrequently, non-condensing)

Maximum altitude

2000 m (Above sea level)

Conformance / approvals

Approvals

ƚ ƒ »

Safety data

Stop category according to IEC 60204

0 , 1

Safety parameters for IEC 61508 - High demand

SIL

PFH

1.89 x 10

-9

Demand rate

< 12 Months

Proof test interval

240 Months

Duration of use

240 Months

Data only applies if the safety function is demanded at least once a year and the signal contact is read back.

The specifications apply assuming the following calculation basis

www.phoenixpowersupply.co.uk

Summary of Contents for 2981428











Search results

Summary of Contents for 2981428

Reviews:

Related manuals for 2981428

Brands by name

Popular brands

Phoenix Contact 2981428, Manual

Search results

Summary of Contents for 2981428

Reviews:

Related manuals for 2981428

Brands by name

Popular brands