background image

onlinecomponents.com

IB IL 24/230 DOR 1/W

5663BC01

17

Ordering Data

Safety Devices

None

Error Messages to the Higher-Level Control or Computer System

None

Air and Creepance Distances (According to EN 50178, VDE 0109, VDE 0110)

Isolating Distance

Air 
Distance

Creepance 
Distance

Test Voltage

Relay contact/bus logic

˜

 5.5 mm 

(0.217 in.)

˜

 5.5 mm 

(0.217 in.)

4 kV, 50 Hz, 1 min

Contact/contact

˜

 3.1 mm 

(0.122 in.)

˜

 3.1 mm 

(0.122 in.)

1 kV, 50 Hz, 1 min

Contact/PE

˜

 3.1 mm 

(0.122 in.)

˜

 3.1 mm 

(0.122 in.)

1 kV, 50 Hz, 1 min

Description

Order Designation

Order No.

Terminal with a digital relay output

IB IL 24/230 DOR 1/W

28 36 43 4

Connector with six connections using the 
spring-clamp method (gray, w/o color print);
Package unit: 10 pieces

IB IL SCN-8-AC

27 40 29 0

Terminals for separating the relay terminal
(separating different voltage areas);
Package unit: 1 set (2 pieces)

IB IL DOR LV-SET

27 42 64 1

Connector for IB IL DOR LV-SET;
Package unit: 1 set (2 pieces)

IB IL DOR LV-PLSET

27 42 66 7

“Configuring and Installing the INTERBUS Inline 
Product Range” User Manual

IB IL SYS PRO UM E

27 43 04 8

Summary of Contents for IB IL 24/230 DOR 1/W



















Reviews: