background image

SD FLASH 512MB MODULAR MUX

8 / 56

PHOENIX CONTACT

105752_en_03

2 Description of the SD FLASH 512MB MODULAR MUX 

multiplexer system

2.1

Hardware and software requirements

– Two ILC 131 ETH Inline controllers (Order No. 2700973)

– Two SD FLASH 512MB MODULAR MUX SD cards (Order No. 2701872) with multi

-

plexer software

– Ethernet cable for directly connecting the two Inline controllers to each other

– Optional: two adapters for wireless communication, e.g., FL EPA 2 (Order 

No. 1005955)

– Required Inline input terminals and Inline output terminals

– Web browser

2.2

Structure of the multiplexer system

Using two SD FLASH 512MB MODULAR MUX SD cards, it is possible to create a multi

-

plexer system consisting of two ILC 131 ETH Inline controllers. You do not need to program 

the Inline controllers. Each station of the multiplexer system consists of one Inline controller 

including the SD card and the connected Inline terminals. Communication between the two 

stations can either be established using an Ethernet cable or a wireless connection.

 

In order 

to be able to communicate via a wireless network, an adapter for wireless communication 

is required for each station (e.g., FL EPA 2 adapter).

Both stations can be integrated into an Ethernet network. The multiplexer software that is 

installed on the SD card is used to implement the required configuration.

The ordering data for hardware, software, and additional documentation can be found in 

Section “Technical data and ordering data” on page 40

.

Summary of Contents for SD FLASH 512MB MODULAR MUX



























































Reviews: