Phoenix Solar TectoFlat Installation Instructions And Use Download | Manualshive

Page: 3 / 27

background image

CONTENTS

PAGE

1. Safety instructions ..............................................................................................................4
2. Tools required.....................................................................................................................5
3. Required documents ..........................................................................................................5
4. Overview of the components ..............................................................................................5
5. Pre-assembly......................................................................................................................7
6. Adjusting the tilt angle ........................................................................................................8
7. Installation instructions .......................................................................................................9
8. Lightning protection ..........................................................................................................15
9. Standards and regulations................................................................................................18
Appendix A Installation of MiaSolé and First Solar modules ................................................17
Appendix B Installation on trapezoidal sheet metal ..............................................................23
Appendix C Installation of wind detector shield……………………….…………………………27

Status 04/12 – Subject to errors and technical modifications
Phoenix Solar AG, Hirschbergstrasse 8, 85254 Sulzemoos, Germany, Phone +49 (0)8135 938 -0, Fax +49 (0)8135 938 - 999

Page 3 of 27

«
1
2
3
4
5
...
»

Summary of Contents for TectoFlat




























Reviews:

No comments

Related manuals for TectoFlat

Brand: TCSM Pages: 24

Isys i/O TPMC-15-CH

Brand: Crestron Pages: 58

Brand: NewLine Pages: 48

Solar Aluflex 237611

Brand: Compass Pages: 7

Brand: Quanmax Pages: 39

Brand: InTouch Pages: 4

Brand: Akcome Pages: 20

touch eTCH-0002

Brand: eSmart Pages: 4

Brand: Energeeks Pages: 26

Brand: TrickleStar Pages: 3

Brand: Roofit.Solar Pages: 25

Brand: Peimar SRL Pages: 12

Brand: Nagasaki Pages: 9

Brand: Nagasaki Pages: 13

Brand: DLG Pages: 44

Brand: FabiaTech Pages: 3

Brand: FabiaTech Pages: 3

Brand: Protech Systems Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands