background image

13

www.UsePhoenix.com • sales@UsePhoenix.com

Toll-Free 1-800-533-7533

Phoenix 4800 Limited Warranty

Warrantor:

Therma-Stor LLC
4201 Lien Rd
Madison, WI 53704
Telephone: 1-800-533-7533

Who Is Covered:

 This warranty extends only to the original end-user of the 4800 and may not be assigned 

or transferred.

First Year Warranty:

 Therma-Stor Products warrants that, for one (1) year the 4800 will operate free from 

any defects in materials and workmanship, or Therma-Stor Products will, at its option, repair or replace 

the defective part(s), free of any charge.

End-User Responsibilities:

 Warranty service must be performed by a Servicer authorized by Therma-Stor 

Products. If the end-user is unable to locate or obtain warranty service from an authorized Servicer, he 

should call Therma-Stor Products at the above number and ask for the Therma-Stor Products Service 

Department, which will then arrange for covered warranty service. Warranty service will be performed 

during normal working hours.

The end-user must present proof of purchase (lease) upon request, by use of the warranty card or other 

reasonable and reliable means. The end-user is responsible for normal care. This warranty does not 

cover any defect, malfunction, etc. resulting from misuse, abuse, lack of normal care, corrosion, freezing, 

tampering, modification, unauthorized or improper repair or installation, accident, acts of nature or any 

other cause beyond Therma-Stor Products’ reasonable control.

Limitations and Exclusions:

 If any 4800 part is repaired or replaced, the new part shall be warranted 

for only the remainder of the original warranty period applicable thereto (but all warranty periods will be 

extended by the period of time, if any, that the 4800 is out of service while awaiting covered warranty 

service).

UPON THE EXPIRATION OF THE WRITTEN WARRANTY APPLICABLE TO THE 4800 OR ANY PART THEREOF, 

ALL OTHER WARRANTIES IMPLIED BY LAW, INCLUDING MERCHANTABILITY AND FITNESS FOR A 

PARTICULAR PURPOSE, SHALL ALSO EXPIRE. ALL WARRANTIES MADE BY THERMA-STOR PRODUCTS 

ARE SET FORTH HEREIN, AND NO CLAIM MAY BE MADE AGAINST THERMA-STOR PRODUCTS BASED ON 

ANY ORAL WARRANTY. IN NO EVENT SHALL THERMA-STOR PRODUCTS, IN CONNECTION WITH THE SALE, 

INSTALLATION, USE, REPAIR OR REPLACEMENT OF ANY 4800 OR PART THEREOF BE LIABLE UNDER 

ANY LEGAL THEORY FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT 

LIMITATION WATER DAMAGE (THE END-USER SHOULD TAKE PRECAUTIONS AGAINST SAME), LOST 

PROFITS, DELAY, OR LOSS OF USE OR DAMAGE TO ANY REAL OR PERSONAL PROPERTY.

Some states do not allow limitations on how long an implied warranty lasts, and some do not allow the 

exclusion or limitation of incidental or consequential damages, so one or both of these limitations may 

not apply to you.

Legal Rights:

 This warranty gives you specific legal rights, and you may also have other rights which vary 

from state to state.

Summary of Contents for 4800 E














Reviews: