Phoenix A10 User Manual Download | Manualshive

Page: 5 / 15

background image

5

Copyright © 2013 Alary Design / PhotoShip One LLC -

www.PhotoShipOne.com

Shoulder Configuration

Shoulder  configuration  is  setup  similar  to  handheld  as  noted  above.    The  same  15mm  rod  mount  and
handles are  used along with  longer rods.    The main  difference being the  Phoenix A10  is mounted on  the
rods inverted, a 15mm  rod shoulder pad is installed and a V-mount  battery is mounted to  the rear of  the
rods for counter balance. it  is important to  note that in this mode the yaw axis setting in  the software GUI
must be inverted. We will discuss that later in the manual.

Figure 10. Shoulder Configuration Assembled

«
...
3
4
5
6
7
...
»

Summary of Contents for A10
















Reviews:

No comments

Related manuals for A10

Brand: Gates Underwater Products Pages: 49

Brand: Gates Underwater Products Pages: 45

Resusci Baby QCPR

Brand: laerdal Pages: 8

Brand: IFM Pages: 9

Brand: Smartech Pages: 8

Tinker PIZZA-BOX/ THERMO-BOX

Brand: RIESE & MULLER Pages: 4

Brand: R&G Pages: 10

Brand: Independence paragliding Pages: 15

PIH-0364X WN IP

Brand: Lilin Pages: 29

Compass 12 Fluid Head

Brand: Miller Pages: 2

Brand: Vintage Air Pages: 28

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

Brand: Stramatel Pages: 10

Brand: Nippon Gases Pages: 28

Brand: ZEN AROME Pages: 29

Brand: femkes Pages: 7

WAF-5406-PSL-FT Series

Brand: Willoughby Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands