background image

 
 
EDF ENR PWT 

 

 

 

 

 

 

 

D06

P06

01

   

Indice

 

1

   

Date:

   

3

01

13

 

EDF

 

ENR

 

PWT

 

 

Société

 

par

 

actions

 

simplifiée

 

à

 

associé

 

unique

 

 

au

 

capital

 

de

 

37

 

505

 

000

 

 ‐ 

 

513

 

281

 

972

 

RCS

 

NANTERRE

 

Siège

 

social

 

:

 

100

 

Esplanade

 

du

 

Général

 

de

 

Gaulle

 

 

Cœur

 

Défense

 

 

Tour

 

B

 

92932

 

Paris

 

La

 

Défense

 

cedex

.

 

33,

 

Rue

 

Saint

 

Honoré

 ‐ 

Z.I.

 

Champfleuri

   

38300

 

Bourgoin

 

Jallieu

 ‐ 

France

 

Tel

 

:

 

04

 

74

 

93

 

80

 

20

 ‐ 

Fax

 

:

 

04

 

74

 

93

 

80

 

40

 

 

current (for a total of 1.56), and a correction factor for an open circuit (see Table 1 below) for sizing conductors and 

fuses may be applicable, depending on your local regulations. 

 

 

Table 1: Low temperature correction factors table for open-circuit voltage 

 

 

 
 
4.0  STORAGE AND UNPACKING 

 

Precautions and General Safety 

 

Store modules in a dry and ventilated room. 

 

Do not allow children and unauthorized persons near the installation site or storage area of modules. 

 

Do not transport modules in an upright position.   

 

Unpacking module pallet with care and follow the unpacking steps marked on the pallet. Be careful when 

unpacking, transporting and storing the modules.     

 

Do not carry a module by its wires or junction box. Carry a module by its frame with two or more people.   

 

Do not place modules on top of each other.   

 

Do not place excessive loads on the module or twist the module frame.

 

 

 

Do not stand, step, walk and/or jump on the module.     

 

Do not drop or place objects on the modules (such as tools.)     

3

Summary of Contents for EDF ENR PWT











Reviews: