background image

PKI-0081

-8-

PIAA LIMITED WARRANTY

www.piaa.co.jp

www.piaa.com

If a PIAA product is suspected of being defective, it must be submitted freight prepaid, to either an 

authorized dealer or distributor for warranty inspection within the 2 year warranty period. The receipt 

or other proof of purchase and a description of the problem must be included. The returned product will be 

inspected.  If the product is found to be defective and covered by this Limited Warranty, the sole remedy is 

repair or replacement, at PIAA's option. A repaired or replacement product will be shipped back at no charge. 

Removal, installation, or reinstallation costs are not covered by this 2 year Limited Warranty.

 

This Limited Warranty specifi cally excludes defects resulting from misuse, abuse, neglect, alteration, 

modifi cation, improper installation, unauthorized repairs, submersion, theft, vehicle crash, or by any 

other type of impact. Except for the Limited Warranty stated above, there are no warranties of PIAA 

products or any part thereof, whether express or implied.  Any implied warranty of merchantability 

or any warranty of fi tness for a particular purpose is expressly disclaimed. Some states do not 

permit the disclaimer of implied warranties.

Crash or impact damage is not covered. This can be determined by a chip or scrape on the lens or the

 housing. Stress cracks sometimes occur when the lens is subjected to sudden and extreme temperature

 changes. A stress crack has no chip or other sign of impact. Stress cracks are covered under warranty.

In no event shall PIAA be liable for any damages whatsoever (including, without limitation, consequential

damages, incidental damages, or damages for loss of use, loss of business profi ts, business interruption,

loss of business information, loss of time, inconvenience, or other losses) arising out of the use, misuse, 

or inability to use a PIAA product. PIAA reserves the right to change the design of its products without any 

obligation to modify any previous product. This warranty gives you specifi c legal rights.  You may also 

have other rights that vary from state to state.

 

REPAIR AND REPLACEMENT

EXCLUSIONS

LENS CRACKS

EXCLUSION OF DAMAGES

Summary of Contents for LPX570









Reviews: