Piaa RF10 Installation Instructions Manual Download

Page: 3 / 15

-3-

PKI-0041-5-E

※ Verify all the parts are included. If a part is missing, please contact your local distributor.
※ Depending on mounting methods, some parts may not be used.

Product Details

① Lamp main unit (1 unit)

② Installation
bracket A (2pcs)

⑥ Hexagon socket head bolt
(M10) (2pcs)

⑤ Rubber cushion
(2pcs)

③ Hexagon head bolt
(2pcs)

④ Hex nut（L ／ M10）
(2pcs)

⑱ Hex nut
(L ／ M8) (2pcs)

⑧ Hex nut（S ／ M10）
(2pcs)

⑨ Side cap (4pcs)

⑦ Slider (2pcs)

This product package contains
one the following lamp unit types
"RF6", "RF10" or "RF18"

RF6

RF10

RF18

⑩ Installation
bracket B (L)(1pc)

⑪ Installation
bracket B (R)(1pc)

⑬ Washer
(S ／ M6) (8pcs)

⑭ Spring washer
（S ／ M6）(4 pcs)

⑫

Hexagon socket head

button bolt

(S ／ M6)

(4pcs)

⑮

Hexagon socket head

button bolt

(L ／ M8)

(2pcs)

⑯ Washer
(L ／ M8) (2pcs)

⑰ Spring washer
(L ／ M8)(2pcs)

Mounting method A

Mounting method B

Parts to be used in Mounting method A.

Parts to be used in Mounting method B.

Summary of Contents for RF10
















Search results

Summary of Contents for RF10

Reviews:

Related manuals for RF10

Brands by name

Popular brands

Piaa RF10, Installation Instructions Manual

Search results

Summary of Contents for RF10

Reviews:

Related manuals for RF10

Brands by name

Popular brands