Piaa RF10 Installation Instructions Manual Download | Manualshive

Page: 8 / 15

background image

-8-

PKI-0041-5-E

● Use the recommended torque and apply equal force when tightening the Hexagon socket head bolt
(M4/Item ⑳ ).

● If connecting 3 lamps in a row, make sure to install the right number of bracket(s) for each size f a lamp.

● When connecting lamp units RF6 and RF10 , we recommend that 2 Installation brackets A (Item ② )
be used on each lamp unit.
If there is a problem with the installation position and only one Installation bracket A can be installed on
each lamp, install it on the outer hole from center.

● When installing and using RF18 unit, make sure to install 2 Installation brackets A (Item ② ) at
2 positions on each lamp.

After installing the lamp, follow the P13 【7】

Relay Harness Installation Sequence .

Installation bracket A

Center

Center

Center

Center

Center

Center

«
...
6
7
8
9
10
...
»

Summary of Contents for RF10
















Reviews:

No comments

Related manuals for RF10

Brand: UnionSpecial Pages: 56

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

Brand: HAMAR LASER Pages: 49

Brand: R.M. Young Pages: 10

Brand: K-LASER Pages: 70

Brand: K-LASER Pages: 72

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: laguna Pages: 16

Brand: Lafayette Pages: 2

Brand: Olsen Pages: 58

Brand: Garmin Pages: 41

Carestation 620

Brand: GE Pages: 268

Brand: GE Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands