background image

 

Try rebooting both your Pico/Z and the PicoStill 

 

Reboot your router 

If this is something that is becoming a more frequent issue: 

 

Make sure that you have a strong WiFi signal where you are operating your PicoStill 

 

Sometimes this can happen if there is a lot of EMF interference in the area. Try moving 

your PicoStill and Pico/Z away from any major electrical appliances or other possible 

sources. 

 

Sometimes the issue can just be the room or area itself. Try moving and operating your 

PicoStill in a different area and see if this decreases the frequency of these errors. 

If you were unable to find or repair the leak, 

Go To ‘PicoBrew Support’

 
 

I purchased or am selling a used PicoBrew product 

 

Please send an email to pbfg.deregister@outlook.com with the product’s serial number from 

the email account currently associated with the device. We will attempt to deregister the 

device so it can be used again by a new user. Please allow 7-10 business days and understand 

that no replies or support will be provided at this email address. 

 
 

PicoBrew Support 

 

Unfortunately PicoBrew is unable to provide additional support at this time. Your problem 

exceeds the scope of this basic troubleshooting guide which has been provided as a courtesy. 

PicoBrew users have several active communities on Facebook and other sites that may be 

able to answer your questions. Please do not continue to operate a machine that was not 

repairable under this guide. 

 

Summary of Contents for PicoStill













Reviews: