background image

Ideal setup:

>For both surround and stereo mode, position the P SUB 1 MKII 

as close to the two front loudspeakers as possible 

>The two chassis of the P SUB 1 MKII should face left and right 

with the connection terminal facing the wall 

>As the sound is directed from the sides of the chassis, only a 

small clearance from the wall is required (approx. 30 cm) 

>Do not in any way prevent the free movement of the P SUB 1 MKII 

>Do not place any objects such as vases etc. on the P SUB 1 MKII 

so as avoid the possibility of accidents

The P SUB 1 MKII can be installed flexibly and easily. Due to its relatively small size, it can be integrated in any unit and can be 

positioned as required virtually anywhere in the room. However, to ensure the most natural sound, the P SUB 1 MKII should be placed 

on the floor near the two front loudspeakers. 

PIEGA P SUB 1 MKII

Recommendations for ideal positioning...

Installation Instructions

6

Note:

Frequencies below 100 Hz cannot be localized by the human ear.   

                           >The exact positioning of the P SUB 1 MKII is largely unnecessary...! 

Surround mode

Stereo mode

Summary of Contents for P SUB 1 MKII

















Reviews: