2017PC-P01/09
18
3.0 FUEL
The wood pellet is obtained by pressing wood sawdust left over from
theworkingofnaturaldriedwood.Thetypicalsmall,cylindricalformis
obtained by passing the material through a die.Thanks to lignin,a natural
elementwhich isreleased duringthepressingoftheraw material,the
pellets acquire a good consistency and compactnesswithout requiring
treatment with additives or caking agents.
There are various types of pellet on the market with qualities and
characteristics that vary depending on the processes they have
undergone and the type of wood used in their production.
Since the characteristics and quality of the pellet considerably
affect stove performance, efficiency and proper operation,we
recommend that you use high-quality pellets.
Manufacturer and distributor has tested and programmed its
stoves and can ensure best performance and trouble-free
operation using pellets with the following specific
characteristics:
Pellet characteristics
Components
natural pure wood pellet
Length, approx.
¼” – 1 ¼” / (7 – 30 mm)
Diameter, approx.
0.23” – 0.25” / (6 – 6.5 mm)
Apparent density, approx.
40.5 lb/ft3 / (650 kg/m3)
Net heat value, approx.
8000 BTU/lb / (5 kWh/kg)
Moisture content, approx.
< 8%
Residual ash, approx.
< 0.5%
N.B. the above data refer to beech/fir wood pellets
To ensure trouble-free operation:
DO NOT
use pellets with dimensions other than those recommended by
themanufacturer.
DO NOT
use poor quality pellets containing sawdust,bark, maize, resins
or chemical substances, additives or adhesives.
DO NOT
use damp pellets.
Choosing other and unsuitable pellets
- obstructs the grate and flue gas pipes;
- increases fuelconsumption;
- reduces efficiency;
- means that proper stove operation cannot be guaranteed;
- causesdirttobuildupontheglass;
- leaves particles which have failed to burn and heavy cinders.
The presence of moisture inthe pellets increases their volume and
causes them to split which in turn causes:
- malfunction of the fuel-loading system;
- inefficient combustion.
Pellets should be stored in a sheltered, dry place.
To use good quality pellets with dimensions and heat-producing
properties other than those recommended above, it will be necessary to
change the stove operating parameters.
The use of cordwood is prohibited.Do not burn garbage or
flammable fluids such as gasoline, naphtha or engine oil.
This“customisation”ofstovesettingsmustbecarriedoutby
authorisedpersonnelbydistributor
Using pellets that are out of date or not in conformity with
the manufacturer’s recommendations not only damages the
stove and jeopardises its performance, but can render the
guarantee null and void and relieves the manufacturer of all
liability.
4.0 PREPARING FOR INSTALLATION
To prevent accidents or damage to the product we recommend the
following:
- unpacking and installation must be carried out by at least two people;
- everyoperationinvolvingmovement of theproduct must becarried
out with the proper tools in full compliance with current safety
regulations;
- the packaged product must be kept in the position according to the
directions shown by the diagrams and notices on the pack;
- if ropes,straps or chainsare used,ensurethatthey areableto take
theweightofthepackandthattheyareingoodcondition;
- never stand in the vicinity of loading/unloading equipment (forklift trucks, cranes etc);
Unpack the product being careful not to damage or scratch it, take the accessories pack and any pieces of polystyrene or cardboard
used to wedge moveable parts etc. out of the stove firebox. Keep packaging (plastic bags, polystyrene, etc.) out of reach of children,
since it could be a potential source of danger,and dispose of according to local regulations.
To make moving and handling of the stove easier for installation purposes, it is advisable to remove the cladding in accordance with
the procedure described in the paragraph “REMOVING THE CLADDING”and then refit it upon completion of installation. If you decide
to install the stove without removing the cladding, take great care not to buckle, scratch or in any way damage the bottom of the side
panels and the lower frontpanel.
Installation and assembly of the stove must be carried out by qualified personnel.
En
gl
ish
