Pinnacle IKONIC Slimline DKL067, Manual

Double Cylinder Deadbolt  

Step 1: Preparation

Cut template on line (A) & fold on line 
(B) as shown. Place on door at your 
preferred height and mark both the latch 
height (C) and centre of handle hole (D) 
with a pencil. Remove template, and 
measure the thickness of door to mark 
the centre point of the door edge. Use 
a 25mm spade bit to drill an accurate 
hole through the door edge, and using a 
hole saw, drill a 54mm hole through the 
door front.
Accuracy is vital so mark and measure 
carefully and drill holes level.

Instructions to install the Deadbolt.

If installing this deadbolt into a new door you will need the following tools - 25mm spade bit, 2mm drill bit, 54mm hole saw, corded or cordless drill, hammer, wood chisel, Phillips 
head screwdriver, tape and pencil. If you are replacing an existing deadbolt you shouldn’t require the drill, hole saw or spade bit as it will replace most standard dead bolts.

Very Important! 

Please fasten all screws by hand and not an electric screw driver or drill, as over tightening is not recommended.

Step 3: Attaching the cylinders to door.

Fit outside cylinder (without screws) onto the door whilst positioning the spindle horizontally, passing through
cam in latch. Attach internal cylinder with spindle vertically onto door. Align screws and tighten firmly.

How to convert Deadbolt Latch from 60mm to 70mm 

Twist anti-clockwise and pull the latch outwards. Twist clockwise until 
the tab clicks in place at the 70mm square marking. 

Exterior 

deadbolt

Interior 

deadbolt

70

60

Line B

Line A

C

D

60mm

(or 70m

m)

Tip: This spindle must 

       remain horizontal

Tip: This spindle must 

       remain vertical

Twist, pull and 

twist from 60mm 

to 70mm

70

60

WARRANTY CONDITIONS
Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under this warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for 
store locations). Pinnacle Hardware bears reasonable, direct expenses of claiming under the warranty. You may submit details and proof of purchase to our support center for consideration. The warranty covers manufacturer defects in 
materials, workmanship and finish under normal use. This warranty is provided in addition to other rights and remedies you may have under law: Our goods come with guarantees that cannot be excluded under the Australian consumer 
law or Consumer Guarantees Act 1993 (NZ). You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced 
if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty excludes damage resulting from product misuse or product neglect. The warranty covers domestic use only and does not apply 
to commercial applications. This warranty is given by Pinnacle Hardware, ABN 87 614 496 196, 28 Hudson Court, Keysborough Vic 3173, 1800 349 776, Email: support@pinnacle.net.au. New Zealand customers please contact HARCO 
(Harkness & Young Ltd), 09 27 64071, Email: sales@harknessyoung.co.nz. ‘Pinnacle’ is a trademark. © Pinnacle Hardware. Suitable for model number 0123360.

Step 2: Installing the Latch

Place Latch (F) into the 25mm hole 
on the side of the door and mark the 
door around the square plate with 
a pencil. Using a hammer and a 
chisel, check out the timber so that 
the latch fits into the newly created 
recess and finishes flush with the 
door. Once completed push latch 
into place and drill 2mm pilot holes 
into the door edge, then simply 
screw the Timber Screws (G) into 
place. Ensure the arrow on deadbolt 
is facing upwards direction.