Controlling the rest of your system
10
58
En
4
Use
and
to select the first letter of
the brand name of your component then
press ENTER.
This should be the manufacturer’s name (for
example,
P
for Pioneer).
5
Use
and
to select the manufac-
turer’s name from the list then press
ENTER
6
Use
and
to select the proper code
from the list, then try using this remote
control with your component.
The code should start with the component
type (for example,
DVD_5305
). If there is
more than one, start with the first one.
To try out the remote control, switch the
component on or off (into standby) by
pressing
SOURCE
. If it doesn’t seem to
work, select the next code from the list (if
there is one).
•
VSX-D914 model only –
If you can’t find or
properly enter a preset code, you can still
teach the remote individual commands
from another remote control (see
Programming signals from other remote
controls
below).
7
If your component is controlled
successfully, press ENTER to confirm.
The remote LCD display shows
OK
.
Programming signals from
other remote controls
VSX-D914 model only
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals
from the remote control of another compo-
nent. This can also be used to program addi-
tional operations (buttons not covered in the
presets) after assigning a preset code.
1
While pressing the RECEIVER button,
press and hold the 1 button.
The remote LCD display shows
SETUP
.
2
Press the MULTI CONTROL button for
the component you want to control.
The LCD on the remote displays the compo-
nent you want to control.
• You can’t assign the
RECEIVER
button.
3
Use
and
to select LEARN then
press ENTER.
PRES KEY
and the
LEARN
icon show in the
LCD display.
• To exit or cancel press
RECEIVER
.
4
Point the two remote controls
towards each other then press the button
that will be doing the learning on this
receiver’s remote control.
PRES KEY
and the
LEARN
icon start flashing
to indicate the remote is ready to accept a
signal.
• The remote controls should be 1–2 inches
apart.
5
Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s
remote control.
For example, if you want to learn the playback
control signal, press
. The LCD display will
show
OK
if the operation has been learned.
If for some reasons the operation hasn’t been
learned the LCD will display
ERROR
briefly
and then display
PRES KEY
again. If this
happens, keep pressing the (teaching) button
as you vary the distance between the two
remotes, until the LCD display shows
OK
.
1 – 2 inches
+
10
INPUT A
TT
FL
DIMMER
SR
DISC
RECEIVER
MUL
TI C
ONTROL
SOURCE
INPUT SELECT
SETUP
ENTER
TV
C
ONTROL
RECEIVER C
ONTROL
SHIFT
VO
L
DV
D
/L
D
T
V
/S
A
T
D
V
R/V
C
R
T
V C
ONT
CD
TUNE
TUNE
ST
ST
ST
ANDR
A
D
LEVEL
EFFECT
TEST T
O
NE
CH SELECT
AD
V.
SURR
STEREO
SLEEP
INPUT SELECT
TV
C
H
DT
V ON/OFF
TUNER DISPL
AY
MPX AUDIO
CH RETURN SUB
TITLE
MIDNIGHT/ LO
U
D
N
ES
S
DT
V INFO
REC
M
U
T
E
TV
V
O
L
CD-R/T
APE
TUNER
RECEIVER
ENTER
REC ST
OP
HDD
CH
CH
DV
D
D.
A
C
C
E
S
S
TO
P
MENU
DT
V MENU
CL
ASS
MENU
BAND
RETURN
GUIDE
T.
E
D
IT
MC
A
C
C
SETUP
RECEIVER
VSX_D912.book.fm 58 ページ ２００３年１２月５日 金曜日 午前９時４３分
