6
Touch
b
to select DIMENSION and then
touch
c
or
d
to adjust front/surround
speaker balance.
Each time you touch
c
or
d
it moves the
sound towards the front or the surrounds.
+3
to
–
3
is displayed as the front/surround
speaker balance moves from front to sur-
rounds.
7
Touch
b
to select CENTER WIDTH and
then touch
c
or
d
to adjust the center
image.
Each time you touch
c
or
d
it gradually
spreads the center channel sound into the
front left and right speakers over a range
0
to
7
.
3
is the default and it
’
s recommended for
most recordings.
0
places all center sound in
the center speaker.
7
places all center sound
equally in the left/right speakers.
Setting the speaker setting
You need to make with/without (or yes/no) and
size (bass reproducing capacity) selection/ad-
justments depending on the installed speak-
ers. The size needs to be set to
LARGE
(large)
if the speaker is capable of reproducing
sounds of about 100 Hz or below. Otherwise
select
SMALL
(small).
!
Low frequency range is not output if the
subwoofer is set to
OFF
and the front and
rear speakers set to
SMALL
or
OFF
.
!
It is imperative that non-installed speakers
be set to
OFF
.
!
Set the front or rear speaker to
LARGE
if
the speaker is capable of reproducing bass
content, or if no subwoofer is installed.
1
Touch NEXT on the DSP function menu.
2
Touch SPEAKER SETTING.
3
Touch
a
or
b
to select the speaker to
be adjusted.
Each time you touch
a
or
b
selects the speak-
er in the following order:
FRONT
(front speakers)
—
CENTER
(center
speaker)
—
REAR
(rear speakers)
—
SUB WOOFER
(subwoofer)
—
PHASE
(subwoo-
fer setting)
#
You can switch to
PHASE
only when the sub-
woofer has been set to
ON
.
4
Touch
c
or
d
to select the correct size
for the selected speaker.
Each time you touch
c
or
d
selects the size in
the following order:
OFF
(off)
—
SMALL
(small)
—
LARGE
(large)
#
You cannot select
OFF
, when
FRONT
(front
speakers) have been selected.
#
You can select
ON
or
OFF
, when
SUB WOOFER
(subwoofer) has been selected.
#
You can switch
REVERSE
(reverse phase) or
NORMAL
(normal phase), when
PHASE
(subwoo-
fer setting) has been selected.
Correcting the subwoofer
’
s phase
If trying to boost the bass output of the sub-
woofer doesn
’
t do much or rather makes you
feel that the bass gets more murky, this may
indicate that the subwoofer
’
s output and bass
content you hear over other speakers cancel
each other out. To remove this problem, try
changing the phase setting for the subwoofer.
1
Touch NEXT on the DSP function menu.
2
Touch SPEAKER SETTING.
3
Touch
a
or
b
to select SUB WOOFER
(subwoofer).
Each time you touch
a
or
b
selects the speak-
er in the following order:
FRONT
(front speakers)
—
CENTER
(center
speaker)
—
REAR
(rear speakers)
—
SUB WOOFER
(subwoofer)
—
PHASE
(subwoo-
fer setting)
4
Touch
d
to turn subwoofer output on.
#
To turn subwoofer output off, touch
c
.
5
Touch
b
and then touch
c
or
d
to se-
lect the phase of subwoofer output.
Touch
d
to select normal phase and
NORMAL
appears in the display. Touch
c
to
select reverse phase and
REVERSE
appears in
the display.
Available accessories
En
72
Section
04
