AVH-P6400CD/UC
A
B
C
D
1
2
4
1
2
4
86
No
Adjustment item
B SUB BRIGHT
B SUB BRIGHT
Apply a
10-step
signal to
TP ANR,ANG,
ANB.
13
Adjust the first step levels
of the G waveform and the B waveform.
Adjusting
point
Measuring method
and specs.
Remarks
Register
setting of
SA39h
D11 - 8
Register
setting of
SA26h
D7 - 1
Register
setting of
SA39h
D15 - 12
Register
setting of
SA26h
D15 - 9
Register
setting of
SA22h
D15 - 8
B SUB
CONTRAST
B SUB
CONTRAST
Apply a
10-step
signal to
TP ANR,ANG,
ANB.
14
TP VG and VB
Register setting specs : 8
±
2
(specs in designing: 8
±
1)
In the Line adjustment
2 mode, SUB BRI B can be
used as the adjusting point.
Register setting specs: 64
±
3
(specs in designing: 64
±
2)
In the Line adjustment
2 mode, SUB CON B can be
used as the adjusting point.
Apply a
10-step
signal to
TP ANR,ANG,
ANB.
15
16
TP VG and VR
Register setting specs: 8
±
2
(specs in designing: 8
±
1)
In the Line adjustment
2 mode, SUB BRI R can be
used as the adjusting point.
Register setting specs: 64
±
3
(specs in designing: 64
±
2)
In the Line adjustment
2 mode, SUB CON R can be
used as the adjusting point.
Eren if it input a signal for alter nate white into
TP CVBS, it is possible.
(However, adjustment by RGB has priority.)
The luminance level of the input signal: 50%.
In the flicker adjustment mode, COM DC can be
used as the adjusting point.
The luminance level of the
input signal: 50%.
In the flicker adjustment
mode, COM DC can be used
as the adjusting point.
Adjust the first step levels
of the G wave form and the
R waveform.
Adjust the 10th step levels
of the G waveform and the
R waveform.
Keep the unit in the
operation mode for
30 minutes or longer.
Adjust so that the flickers
become minimum in all
Apply a
10-step
signal to
TP ANR,ANG,
ANB.
TP VG and VR
Register
setting of
SA22h
D3 - 0
Horizon dot
position
17
After being witten in,the setting
value of EEP-ROM is checked.
2 mode,DOT CLK can be used
as the adjusting point.
7(0111)
Any input
signal
Adjust the 10th step levels of the
G waveform and the B waveform.
18
Aging
Any input
signal
19
Flicker
Input a signal
for alternate
white and
black lines
to TP CVBS.
Screen
Notes:
1) When the power supply for TC90A64AF is OFF, be careful not to apply any voltage to its terminals except for IIC
lines(SDA and SCL). The IIC lines can accept a maximum of 5V.
2) In the following table, SA**h is a sub-address of TC90A64AF.
Flicker adjustment has been deviated The images flicker.
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
