43
TS5, BCT-1510, BCT-1520,
BCT-1530
•
Pin Function (2/5)
1. The digital encoder video outputs are analogue signals and are not 5V tolerant. The same applies to the video DAC
voltage and current reference pins.
2. The YC0 pin is tri-stated during reset and then sampled at the end of the reset to determine whether the EMI pins are in
STi5510 or STi5512 mode. If the YC0 pin is sampled high (i.e at VDD) then the STi5510 mode is selected for the EMI pins
and a low value selects STi5512 mode. In STi5512 mode the address shift for bank 3 is dependent on the boot bank width
and the strobe pins are tri-stated when the EMI bus is granted to an external DMA device. External 10K
Ω
pull-up or pull-
down resistors should be fitted to the YC0 according to the functionality desired. If this pin is left
not
connected, the pin will
be pulled high by an internal pull-up and will default the EMI pins to STi5510 mode.
Pin
In/Out
Function
SCLK/A_C_STB
out
Serial clock or AC-3 data strobe
PCM_DATA/A_C_DATA
out
PCM data out or AC-3 data out
PCMCLK
in/out
PCM clock
LRCLK/A-WORD_CLK
out
Left/right clock or AC-3 word clock
notA_C_REQ i
n
AC-3
data
request
notA_PTS_STB
in
AC-3 audio PTS strobe
Table 3 AC-3/MPEG1 audio output interface pins
Pin
In/Out
Function
Interrupt0-1
in
Interrupt
Table 4 External interrupt pins
Pin
In/Out
Function
ClockIn
in
System input clock - PLL or TimesOneMode
SpeedSelect0-1
in
PLL speed selector
notRST
in
System reset
CPUAnalyse / TrigIn
in
Error analysis / External trigger input to DCU
CPUReset
in
Soft reset for analyzing from OS-Link
ErrorOut / TrigOut
1
in/out, out
Error indicator / Signal to trigger external debug circuitry (e.g. LSA)
Table 5 System services pins
1. This pin is tri-stated during reset and then sampled at the end of the reset to determine whether the OS-Link is active and
to determine the function of the shared CPUAnalyse / TrigIn and the ErrorOut / TrigOut, as described in the
System Serv-
ices chapter. If the ErrorOut pin is sampled high (i.e at VDD) then the DCU signals (TrigIn and TrigOut) are selected and a
low value indicates OS-Link signals (i.e. CPUAnalyse, ErrorOut) are to be used. External 10K
Ω
pull-up or pull-down resis-
tors should be fitted to the ErrorOut according to the functionality desired.
Summary of Contents for BCT-1510
