background image

En

2

WARNING

This equipment is not waterproof. To prevent a fire or 
shock hazard, do not place any container filled with 
liquid near this equipment (such as a vase or flower 
pot) or expose it to dripping, splashing, rain or 
moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame 
sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in 
accordance with the manufacturer’s 
instructions.
Do not install near any heat sources such as 
radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce 
heat.
Do not defeat the safety purpose of the polarized 
or grounding-type plug. A polarized plug has two 
blades with one wider than the other. A 
grounding type plug has two blades and a third 
grounding prong. The wide blade or the third 
prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an 
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or 
pinched particularly at plugs, convenience 
receptacles, and the point where they exit from 
the apparatus.

1) 

    

 

2) 

    

3)  

    

4)  

    

5)     

 

6)  

    

7)

   
8)

   
9) 

 
  

 

10)

Only  use  attachments/accessories  specified  by 
the manufacturer.
Use only with the cart, stand, tripod, bracket, or 
table specified by the manufacturer, or sold with 
the apparatus. When a cart is used, use caution 
when moving the cart/apparatus combination to 
avoid injury from tip-over.

Unplug  this  apparatus  during  lightning  storms 
or when unused for long periods of time.
Refer all servicing to qualified service personnel. 
Servicing is required when the apparatus has 
been damaged in any way, such as power-supply 
cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the 
apparatus has been exposed to rain or moisture, 
does not operate normally, or has been dropped. 

D3-7-13-69_En

11)

12)

13)

14)

VENTILATION CAUTION

When installing this unit, make sure to leave space 
around the unit for ventilation to improve heat radiation 
(at least 30 cm at top, 30 cm at rear, and 30 cm at each 
side).

WARNING

Slots and openings in the cabinet are provided for 
ventilation to ensure reliable operation of the product, 
and to protect it from overheating. To prevent fire 
hazard, the openings should never be blocked or 
covered with items (such as newspapers, table-cloths, 
curtains) or by operating the equipment on thick carpet 
or a bed.

D3-4-2-1-7b*_A1_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the

instructions, put them away in a safe place for future reference.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

The lightning flash with arrowhead symbol, 
within an equilateral triangle, is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR 
BACK). NO USER-SERVICEABLE PARTS 
INSIDE. REFER SERVICING TO QUALIFIED 
SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1b_A1_En

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_A1_En

Information to User

Alterations or modifications carried out without 
appropriate authorization may invalidate the user’s 
right to operate the equipment.

D8-10-2_A1_En

This product is for general household purposes. Any 
failure due to use for other than household purposes 
(such as long-term use for business purposes in a 
restaurant or use in a car or ship) and which requires 
repair will be charged for even during the warranty 
period.

K041_A1_En

Operating Environment

Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH 
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in 
locations exposed to high humidity or direct sunlight (or 
strong artificial light)

D3-4-2-1-7c*_A1_En

WARNING: 

Handling the cord on this product or 

cords associated with accessories sold with the 
product may expose you to chemicals listed on 
proposition 65 known to the State of California and 
other governmental entities to cause cancer and 
birth defect or other reproductive harm.

D36-P5_B1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the 
plug by tugging the cord and never touch the power 
cord when your hands are wet as this could cause a 
short circuit or electric shock. Do not place the unit, a 
piece of furniture, etc., on the power cord, or pinch the 
cord. Never make a knot in the cord or tie it with other 
cords. The power cords should be routed such that they 
are not likely to be stepped on. A damaged power cord 
can cause a fire or give you an electrical shock. Check 
the power cord once in a while. When you find it 
damaged, ask your nearest PIONEER authorized 
service center or your dealer for a replacement.

S002*_A1_En

IMPORTANT NOTICE

THE MODEL NUMBER AND SERIAL NUMBER OF 
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON PAGE 11 FOR 
FUTURE REFERENCE.

D36-AP9-3*_A1_En

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a 
safe level – a level that lets the sound come through 
clearly without annoying blaring or distortion and, most 
importantly, without affecting your sensitive hearing. 
Sound can be deceiving. Over time, your hearing 
“comfort level” adapts to higher volumes of sound, so 
what sounds “normal” can actually be loud and 
harmful to your hearing. Guard against this by setting 
your equipment at a safe level BEFORE your hearing 
adapts.

ESTABLISH A SAFE LEVEL:

•  Set your volume control at a low setting. 
•  Slowly increase the sound until you can hear it 

comfortably and clearly, without distortion. 

•  Once you have established a comfortable sound 

level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING 
GUIDELINES:

•  Do not turn up the volume so high that you can’t 

hear what’s around you.

•  Use caution or temporarily discontinue use in 

potentially hazardous situations.

•  Do not use headphones while operating a motorized 

vehicle; the use of headphones may create a traffic 
hazard and is illegal in many areas.

S001a_A1_En

Summary of Contents for BULIT5





























Reviews: