51
CDX-MG6346ZH,MG6446ZH
-
Operating Procedures for Ejecting a Clamped Disc
1
2
3
4
5
6
Select CAM MOTOR using [1], then press the REV direction while the disc is being clamped (CAMSW state is 32).
The CAMSW status indication sequentially changes through 32
→
33
→
23
→
22.
When the disc to be ejected is not identical with the disc being clamped, select the [2] ELV MOTOR in the vicinity of where
the display changes from 22 to 20, then match the elevation to the disc to be ejected according to the following procedures:
After selecting ELV MOTOR, lower the elevation until the ELV position display becomes 01 (1st disc) using the REV direction.
Drive the elevation up until the display is changed to 10. This is the elevation where the second disk is situated.
The next display of 10 tells you the elevation of the 3rd disc. Repeating this operation allows you to establish an elevation
matching each disc. (When the elevation is driven from the 1st through 6th disc, the status display changes as
01
→
11
→
10
→
11
→
10
→
11
→
10
→
11
→
10
→
11
→
10.)
(When the disc to be ejected coincides with the disc being clamped, the above operations are not necessary.)
Select the [1] CAM MOTOR and then, using the REV direction, drive it until the display changes from 20 (or 22) to 21 and 31.
Select the [2] ELV MOTOR, then drive the tray of the disc to be ejected up to the EJECT/LOAD position (using the FWD direction).
Select the [4] CAM+LOAD MOTOR, then drive it in the REV direction until the display changes from 31 to 30 and 10.
The door will open immediately before the display changes to 10 and part of the disc will be pushed out.
When 10 is displayed, select the [3] LOAD MOTOR, then drive it in REV direction until the disc is completely ejected.
Summary of Contents for CDX-MG6056ZH
