3
Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
REPEAT
(repeat play)
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select a repeat play range.
For details, refer to
Selecting a repeat play range
on
the previous page.
3
Press
M.C.
to confirm the selection.
RANDOM
(random play)
1
Press
M.C.
to turn random play on or off.
PAUSE
(pause)
1
Press
M.C.
to pause or resume.
S.RTRV
(sound retriever)
Automatically enhances compressed audio and re-
stores rich sound.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the desired setting.
For details, refer to
Enhancing compressed audio
and restoring rich sound (sound retriever)
on the
previous page.
3
Press
M.C.
to confirm the selection.
Audio Adjustments
1
Press M.C. to display the main menu.
2
Turn M.C. to change the menu option
and press to select AUDIO.
3
Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
FAD/BAL
(fader/balance adjustment)
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between fader (front/rear) and
balance (left/right).
3
Turn
M.C.
to adjust speaker balance.
!
When the rear output and RCA output setting are
SW
, you cannot adjust front/rear speaker balance.
Refer to
SW CONTROL
(rear output and subwoofer
setting)
on the next page.
EQUALIZER
(equalizer recall)
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the equalizer.
DYNAMIC
—
VOCAL
—
NATURAL
—
CUSTOM
—
FLAT
—
POWERFUL
3
Press
M.C.
to confirm the selection.
TONE CTRL
(equalizer adjustment)
!
Adjusted equalizer curve settings are stored in
CUSTOM
.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to select
BASS
(bass)/
MID
(mid)/
TRE-
BLE
(treble).
3
Turn
M.C.
to adjust the level.
Adjustment range:
+6
to
-6
LOUDNESS
(loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the desired setting.
OFF
(off)
—
LOW
(low)
—
HIGH
(high)
3
Press
M.C.
to confirm the selection.
SUBWOOFER1
(subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the desired setting.
NORMAL
(normal phase)
—
REVERSE
(reverse
phase)
—
OFF
(subwoofer off)
3
Press
M.C.
to confirm the selection.
SUBWOOFER2
(subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between the cut-off frequency
and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)
—
Output level (Output level display
flashes.)
3
Turn
M.C.
to select the desired setting.
Cut-off frequency:
50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
Output level:
-24
to
+6
En
8
Section
02
Operating this unit
SLA
(source level adjustment)
SLA
(Source Level Adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
Settings are based on the FM volume level, which
remains unchanged.
!
The AM/MW/SW volume level can also be ad-
justed with this function.
!
When selecting FM as the source, you cannot
switch to
SLA
.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range:
+4
to
–
4
3
Press
M.C.
to confirm the selection.
Initial Settings
1
Press S (SRC/OFF) and hold until the
unit turns off.
2
Press M.C. and hold until function name
appears in the display.
3
Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET
(setting the clock)
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to select the segment of the clock dis-
play you wish to set.
Hour
—
Minute
3
Turn
M.C.
to adjust the clock.
FM STEP
(FM tuning step)
The FM tuning step employed by seek tuning can be
switched between 100 kHz, the preset step, and 50
kHz.
!
If seek tuning is performed in 50 kHz steps, sta-
tions may be tuned in imprecisely. Tune in the sta-
tions with manual tuning or use seek tuning
again.
!
The tuning step remains at 50 kHz during manual
tuning.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the FM tuning step.
50 KHZ
(50 kHz)
—
100 KHZ
(100 kHz)
3
Press
M.C.
to confirm the selection.
AM STEP
(AM tuning step)/
MW STEP
(MW tuning
step)
DEH-2350UB and DEH-2350UBG:
AM STEP
DEH-2350UBSW:
MW STEP
The AM/MW tuning step can be switched between 9
kHz, the preset step, and 10 kHz. When using the
tuner in North, Central or South America, reset the
tuning step from 9 kHz (531 kHz to 1 602 kHz allow-
able) to 10 kHz (530 kHz to 1 640 kHz allowable).
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the AM/MW tuning step.
9 KHZ
(9 kHz)
—
10 KHZ
(10 kHz)
3
Press
M.C.
to confirm the selection.
AUX
(auxiliary input)
Activate this setting when using an auxiliary device
connected to this unit.
1
Press
M.C.
to turn
AUX
on or off.
USB
(plug and play)
This setting allows you to switch your source to
USB
automatically.
1
Press
M.C.
to turn the plug and play function on
or off.
ON
–
When USB storage device is connected, de-
pending on the type of device, the source is auto-
matically switched to
USB
when you turn on the
engine. If you disconnect your USB storage de-
vice, this unit
’
s source is turned off.
OFF
–
When USB storage device is connected,
the source is not switched to
USB
automatically.
Please change the source to
USB
manually.
SW CONTROL
(rear output and subwoofer setting)
En
9
English
Section
02
Operating this unit
<CRD4530-A/N>5
Summary of Contents for DEH-2350UB
Page 62: ... CRD4530 A N 62 ...
Page 63: ... CRD4530 A N 63 ...
