Routing the optical cable
Precaution:
•
Try not to bend the optical cable sharply. If it is
necessary to bend it sharply, make sure that the
bending radius is at least 25 mm (1 inch), other-
wise the cable will not transfer signals properly
and so this unit will not work properly.
•
Route the optical cable so that nothing heavy
rests on it, and so that it cannot be stepped on or
caught in anything – for instance, a door.
•
Make a loop of diameter at least 200 mm (7-7/8
inches) with the remaining optical cable so that
the cable does not get strained.
•
When plugging the optical cable into the unit,
use the supplied cable clamps to prevent the
cable from being bent sharply.
•
Route the optical cable so that it does not get
caught in moving parts such as the gear shift,
hand brake, or seat sliding mechanism. Keep the
cable away from hot spots, such as near the
heater outlet.
Using the corrugated tube
To prevent the optical cable from being strained,
use the corrugated tube after cutting it to the cor-
rect length.
• Insert the optical cable into the cor-
rugated tube.
Mounting the clamp
The clamp is used to secure the optical cable
when using it. The other clamp is installed on the
back side of the head unit similarly and used to
secure the optical cable.
1. Insert the clamp in the direction
indicated in the figure, and turn it 90
degrees to lock.
2. Secure the optical cable.
Optical cable
Clamp
Corrugated tube
Optical cable
Note:
•
Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.
•
Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
•
Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
•
Install the unit where it does not get in the dri-
ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
•
When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
•
Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
•
Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
•
If this unit is installed in the passenger compart-
ment, anchor it securely so it does not break free
while the car is moving, and cause injury or an
accident.
•
If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched
in the mechanism and cause a short circuit.
Installing the unit
Mounting with brackets
Mounting with velcro tape
Thoroughly wipe off the surface before affixing
the velcro tape.
Car mat or chassis
Velcro tape
Screw
(4
×
8 mm)
Car mat or chassis
Bracket
Tapping screw (4
×
12 mm)
Drill 2 to 2.5 mm
diameter holes.
Do not close this area.
Connecting and installing the
optical cable connection box
Connecting the optical cable
• Connect the optical cable to the
optical cable connection box.
Installing the optical cable
connection box
• When installing the optical cable
connection box with the velcro
tape.
Install the optical cable connection box
using the velcro tape in the ample
space of the console box.
• When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection
box with the protection tape and fasten
with the power code using the lock tie.
Fasten with the lock tie
Wrap with the protection tape
Velcro tape (hard)
Velcro tape (soft)
Optical cable
Installation
<ENGLISH>
