Recording
06
62
En
8 : 00
11 : 00
9 : 00
10 : 00
Program 1
Prog.1
Deleted Parts
Non Recorded Portion Parts
Prog.2
Prog.3
Program 2
Program 3
Recording
Control Settings
Checking or changing the timer recording
When you want to check the selected timer recording,
follow the steps
1
and
2
of “Setting timer recording” and
display the TIMER REC SET screen.
To change the timer recording, select the program to be
changed and press
ENTER
. The changing method is the
same as that for the recording a program for the first
time.
Cancelling the timer recording
Display the TIMER REC SET screen.
Select the program you want to cancel and press
CANCEL
, then the selected program will be erased from
the timer recording list.
In case timer programs-overlap
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
time has priority over the next recording time as shown
in the diagram below.
In this case, the next recording time is delayed a
maximum of about 1 minute.
10 Press
or
to select “REC MODE” and press
ENTER.
The recording modes for the media selected in “REC
TO” item are listed.
Select the recording mode and press
ENTER
.
For the recording modes in VCR, see page 49. For the
recording modes in DVD, see page 53.
ENTER
RETURN
BACK
END
SELECT
SETUP
ENTER
SETUP MENU
DATE
START
END
CH
REC
TO
REC
MODE
NEW
TYPE
DATE (MM/DD)
START
END
CH
REC TO
REC MODE
ONCE
12
DVD
SP
OK
11/20(TH)
08:00PM
09:30PM
LP
11 Select “OK” and press ENTER.
The timer program is determined and the TIMER REC
SET screen appears again.
12 When you enter the other program for the
timer recording, repeat the steps 3 to 11.
13 Press SETUP.
The TIMER REC SET screen disappears and the display
will return to the normal screen.
14 Press TIMER REC. In five minutes before your
Timer Recording starts, the CH will change to the
programmed CH automatically and the unit stand
by recording.
To extend the timer recording time
Press
TIMER REC
for 2 seconds while it is timer
recording. (You may also use normal recording or OTR).
Note
• If you press
STANDBY/ON
and it goes into the
STANDBY mode, if you then press
TIMER REC
, the
timer recording will end.
Note
• Recording starts a few seconds before the preset
starting time.
• You cannot use the timer recording for the both
DVD and VCR at the same time.
• The timer recording program is stopped during
timer recording, the stopped program is not erased
from the timer recording list. In this case, please
cancel the program, otherwise the stopped
program will be activated if the unit returns to timer
recording standby mode.
• If a recordable tape is not inserted or no disc space
is available, the timer record indicator “
”
flashes, and “TIMER RECORDING ERROR. PLEASE
CHECK THE DISC OR TAPE.” appears on the
screen. Replace the tape or disc to allow recording.
• If you perform any operation during timer recording,
the power will not go OFF when timer recording
finishes. To turn the power OFF, press
STANDBY/ON
.
• From about 6 minutes before timer recording
starts, some operations cannot be done.
• If you set recording to start less than 6 minutes
ahead of time, the power will not turn OFF after
recording finishes.
• If the recording media fills up during timer recording,
“
” will flash and the power will not turn OFF.
Also, any timer recording scheduled for later is
cancelled.
2J40801B_En_59_64
5/29/06, 4:50 PM
62
Summary of Contents for DVR-RT502
Page 1: ... ...
Page 93: ...Additional information 09 93 En ...
Page 94: ...Additional information 09 94 En ...
