PRO-730HDI
103
5
6
7
8
5
6
7
8
C
D
F
A
B
E
Adjustment data:
MAX
1FF
100
001
CNT
000
3FF
2FF
MIN
200
Data can be adjusted with the VOL+ and VOL- keys.
F
DFH
1A0
Screen indication
The cross-hatch signal is generated inside the unit, and is auto-
matically displayed in OFFSET CONVER. mode and MANUAL
CONVERGENCE mode. You can turn on and off the cross-hatch
signal with the YELLOW key.
Screen mode:
F
: FULL
H : HD
The Screen modes change cyclically with each press of the
SCREEN mode key.
Adjustment items can be selected with the numeric keys.
See Table 2.
A
A
B
B
C
C
DIGITAL CONV. ASSY
IC1203
IC1203: 24LC64(I)P
CN1201
CN1202
CONVERGENCE ADJUSTMENT
1. Procedures
1. When replacinf the DIGITAL CONV. Assy, replace the
EEPROM of new DIGITAL CONV. Assy with the EEPROM
of old DIGITAL CONV. Assy.
2. Check the initial data for the convergence adjustment.
3. Perform the coarse adjustment for the green to roughly correct
distortion of the green.
4. Fine-adjust the green to eliminate any distortion. The green
becomes the standard for the red and the blue.
If necessary, repeat steps 3 and 4. Green adjustment is
completed.
5. Perform the coarse adjustment for the red by roughly
converging the red with the green.
6. Fine-adjust the red until the red is completely converging with
the green.
If necessary, repeat steps 5 and 6. Red adjustment is completed.
7. Perform the coarse adjustment for the blue by roughly
converging the blue with the green.
8. Fine-adjust the blue until the blue is completely converging
with the green.
If necessary, repeat steps 7 and 8. Blue adjustment is
completed.
9. Display the green, red, and blue colors at the same time to check
the convergence. Readjust the convergence if necessary.
5
2. Prior to Adjustment
There are five screen modes, but convergence adjustment is
required for two mode. For adjustment, input the following video
signal:
Screen Mode
Input Signal
1. FULL (FULL, 4:3 NORMAL)
(ZOOM)
(CINEMA WIDE)
(NATURAL WIDE)
2. HD (HD/DTV)
HD/DTV (1080i) signal
NTSC : Stable signal source, such as an SG or an LD/DVD player.
HD
: Stable signal source, such as an HD SG or a DTV tuner
(SH-D09, etc.)
Table 1 Input signal
When CRTs are replaced or when the deflection yoke is moved,
perform the deflection yoke adjustment, horizontal and vertical
size adjustments, and centering magnet adjustments before the
convergence adjustment. (See Pages 157, 159 and 160.)
3. Convergence Adjustment
3.1 Replacement of the EEPROMs Inside
the DIGITAL CONV. Assy
VIDEO UCOM
SERVICE ASSY
IC1903
24LC32A(I)P
IC1906
M306V7FGFP
The data stored in the EEPROMs are as follows:
IC1203
OFFSET CONVER. MODE 1 (DFH, DFV)
OFFSET CONVER. MODE 3
Factory-preset values for convergence
User-adjusted values for convergence (CENTER, MULTI-POINT)
IC1903 (VIDEO UCOM SERVICE Assy)
OFFSET CONVER. MODE 1 (except DFH and DFV)
OFFSET CONVER. MODE 2
3.2 Confirmation of Convergence Data
The convergence coarse adjustment modes change cyclically, as
shown below, with each press of the INPUT4 key in FACTORY
mode:
Convergence coarse adjustment
DOT key (pressed once)
: OFFSET CONVER. MODE 1
DOT key (pressed twice)
: OFFSET CONVER. MODE 2
DOT key (pressed three times)
: OFFSET CONVER. MODE 3
Cyclical change
Check whether the data of MODE 1 and MODE 2 are as shown in
Table 2.
NTSC (480i) signal
