38
Connecting your equipment
03
Connecting your TV and playback components
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player (BD), etc.), you can connect it
to this receiver using a commercially available HDMI cable.
If the TV and playback components support the
Control
with HDMI feature, the convenient
Control
with HDMI
functions can be used (see
( 5 V 0.9 A )
ASSIGNABLE
ASSIGNABLE
L
R
DVR/BDR
IN
SAT/CBL
IN
OUT
MONITOR
OUT
IN
1
(CD)
PHONO
IN
1
(DVD)
BD
2
(SAT/CBL)
3
(DVR/BDR)
6
4
7 /
/MHL
SIGNAL
GND
3
(HDZONE)
2
1
MAIN
SELECTABLE
ZONE 3
PRE OUT
ZONE 2
PRE OUT
ZONE 3
PRE OUT
ZONE 2
PRE OUT
OPTICAL
COAXIAL
DIGITAL AUDIO
IN
1
(TV)
IN
2
(DVR/BDR)
IN
1
(SAT/CBL)
IN
2
(DVD)
7 /
/MHL
HDMI OUT
HDMI IN
ASSIGNABLE
-
1 7
-
VIDEO/AUDIO
OUT
1
1 2
-
ARC CONTROL
DVR/BDR
IN
ZONE 3
PRE OUT
ZONE 2
PRE OUT
SAT/CBL
IN
OUT
MONITOR
OUT
VIDEO/AUDIO
( 5 V 0.9 A )
ASSIGNABLE
ASSIGNABLE
L
R
IN
1
(CD)
PHONO
IN
1
(DVD)
BD
2
(SAT/CBL)
3
(DVR/BDR)
6
4
SIGNAL
GND
3
(HDZONE)
2
1
MAIN
SELECTABLE
OPTICAL
COAXIAL
DIGITAL AUDIO
IN
1
(TV)
IN
2
(DVR/BDR)
IN
1
(SAT/CBL)
IN
2
(DVD)
7 /
/MHL
HDMI OUT
HDMI IN
ASSIGNABLE
-
1 7
-
VIDEO/AUDIO
OUT
1
1 2
-
ARC CONTROL
DIGITAL OUT
COAXIAL
ANALOG
R
L
AUDIO OUT
HDMI IN
HDMI OUT
HDMI OUT
OPTICAL
HDMI/DVI-compatible
Blu-ray Disc player
Other HDMI/DVI-
equipped component
HDMI/DVI-compatible monitor
Select one
This connection is required in
order to listen to the sound of
the TV over the receiver.
!
When connecting to an HDMI/DVI-compatible monitor using the
HDMI OUT 2
terminal, switch the HDMI
output setting to
OUT 2
or
OUT 1+2
. See
.
In the same way, when an HDMI/DVI-compatible monitor is connected to the
HDMI OUT 3
terminal, switch
the
HDMI
OUT 3
setting to
ON
). In this case,
MAIN/HDZONE
at
ZONE Setup
must be set to
MAIN
!
For input components, connections other than HDMI connections are also possible (see
!
If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
—
When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the
HDMI OUT
terminal, so
there is no need to connect an audio cable. In this case, set
ARC
at
HDMI Setup
to
ON
on
After setting the
ARC
, some time may be required for the connected device to be recognized and the sound to
be produced.
—
If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see
—
Please refer to the TV’s operation manual for directions on connections and setup for the TV.
!
If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal input setting in
accordance with TV performance. When the
4K/60p
setting is changed to
4:4:4
, the video image may not be
output normally unless the HDMI cable supports 4K/60p 4:4:4 24 bit (18 Gbps transmission). In such a case,
select
4:2:0
!
You cannot input 4K/60p 4:4:4 24 bit video from
HDMI
IN 3
to the
IN 6
terminal. Use the
BD IN
,
HDMI
IN 1
or
HDMI
IN 2
terminal.
!
The
HDMI OUT 3
terminal outputs 4K/60p 4:4:4 24 bit video when
MAIN/HDZONE
is set to
MAIN
. When it is
set to
HDZONE
, the 4K/60p 4:4:4 24 bit video is not output.
