58
Basic Setup
04
H: Directly connecting this receiver with a smart phone by wireless (Wireless
Direct)
1 Select ‘Network Connection’ from the Network, Bluetooth menu.
2 Select ‘Wireless Direct’ from the Network Connection menu.
3 Select ‘Security Protocol’ at
i
/
j
.
4 Select the encryption method with
k
/
l
.
!
None
– Does not set the encryption method.
—
Because this connection is not encrypted, there is a slight security risk.
—
When the main power of this receiver is turned off, Wireless Direct is not started when it is turned on next
time, and will operate with the network settings before Wireless Direct is started.
!
WEP
– Set to the WEP method.
—
Even when the main power of this receiver is turned off, Wireless Direct will continuously operate the next
time it is turned on.
5 Select ‘Frequency Band’ at
i
/
j
.
6 Select the frequency with
k
/
l
.
Select the frequency band of
Wireless Direct
connection. If you do not know the frequency band of your equip-
ment, select
2.4GHz
.
!
2.4GHz
– Uses the band of 2.4 GHz.
!
5GHz
– Uses the band of 5 GHz.
7 Select ‘OK’, then press ENTER.
When
WEP
is selected, the WEP KEY input screen is displayed. Enter the WEP KEY in 5 or 13 characters, select
OK
, and press
ENTER
.
8 Select ‘YES’ and press ENTER.
9 Select the SSID shown on the screen of this receiver from the list of wireless connection
LAN’s corresponding to the equipment that you have.
!
If the password is requested, enter the WEP KEY in procedure 7.
Checking the Network Information
The setting status of the following network-related items can be checked.
!
IP Address
(IPv4) – Check the IP address of this receiver.
!
IP Address
(IPv6) – Check the IP address of this receiver.
!
MAC Address
– Check the MAC address of this receiver.
!
Friendly Name
.
!
SSID
– Check the SSID during wireless connection.
!
Network Connection
– Check the network connection status (
Wired
/
Wireless
/
Wireless Direct
).
%
Select ‘Network Information’ from the Network, Bluetooth menu.
Display the setting status of the network-related items.
Performing
Bluetooth
settings
Switches the
Bluetooth
function on/off.
1 Select ‘Bluetooth Setup’ from the Network, Bluetooth menu.
2 Use
k
/
l
to select the setting.
!
ON
– Selected when using the
Bluetooth
function.
!
OFF
– Selected when the
Bluetooth
function is not used.
3 Select ‘OK’, then press ENTER.
The confirmation screen will be displayed. Select ‘
YES
’ and press
ENTER
.
The on-screen display will close, and the home menu will be disabled for about 60 seconds. After 60 seconds,
execute the following operation.
Other network settings
Set the network other than for connection.
1 Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and
then press HOME MENU.
A Graphical User Interface (GUI) screen appears on your TV. Use
i
/
j
/
k
/
l
and
ENTER
to navigate through the
screens and select menu items. Press
RETURN
to exit the current menu.
2 Select ‘Network, Bluetooth’ from the HOME MENU.
3 Select ‘Network Option’ from the Network, Bluetooth menu.
4 Select the setting you want to adjust.
If you are doing this for the first time, you may want to adjust these settings in order:
!
Network Standby
– Even when the unit is in standby mode, it is possible to turn on the power of the unit
from iControlAV5 (
!
Friendly Name
– The name of the receiver displayed on a computer or other device connected to the network
can be changed (
!
AirPlay Password
– Set the password to be entered when playing AirPlay with this receiver (
).
!
Parental Lock
– Restricts usage of network functions (
).
!
Play ZONE Setup
– Select the zone for playing the audio contents of devices in the home network (
).
!
Port Number Setting
– Sets the numbers of the ports where signals from IP Control are received (
).
Network Standby
Set so that the iControlAV5 function connected to the same LAN with the receiver can be used even while the unit
is in standby status.
1 Select ‘Network Standby’ from the Network Option menu.
2 Specify whether the Network Standby is ON or OFF.
!
ON
– Even when the receiver is in standby mode, you can power on the receiver from iControlAV5 on a device
connected to the network. However, when network communications are cut, the receiver will switch to nor-
mal standby mode to conserve power when on standby. In this case, switch the remote control power on.
Also, when using Wireless Direct, the network standby function does not work.
!
OFF
– The iControlAV5 function is not available while the receiver is in standby mode (power consumption
during standby can be suppressed).
Friendly Name
1 Select ‘Friendly Name’ from the Network Option menu.
2 Select ‘Edit Name’ then select ‘Rename’.
If after changing the name you want to restore the name to the default, select
Default
.
3 Input the name you want.
Use
i
/
j
to select a character,
k
/
l
to set the position, and
ENTER
to confirm your selection.
