background image

<ENGLISH>

Connecting the Power Terminal

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive 
terminal (+) and the ground wire to the car body.

1. Pass the battery wire from the

engine compartment to the interior
of the vehicle.

• After making all other connections to the 

amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.

2. Twist the battery wire, ground wire

and system remote control wire.

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

screws.

WARNING

Failure to securely fasten the battery wire to the ter-
minal using the terminal screws could cause the ter-
minal area to overheat and could result in damage
and injury including minor burns.

Connecting the Speaker Output
Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about 
10 mm (3/8 inch) and twist.

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

3. Connect the speaker wires to the

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Fuse (30 A)

Engine
compart-
ment

Interior of
the vehicle

Drill a 14 mm
(1/2 inch) hole
into the vehicle
body.

Insert the O-ring rubber
grommet into the vehicle
body.

Positive terminal

GND terminal

Power terminal

Battery wire

System remote 
control terminal

System remote 
control wire

Ground wire

Speaker 
output
terminal

Terminal screw

Fuse (30 A)

Speaker wire

Summary of Contents for GM-6200F














Reviews: