Listening to your system
23
En
04
04
English
Français
Español
Using surround back channel processing
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby Digital
EX or DTS-ES), or you can choose to always use 6.1 or 7.1
decoding (for example, with 5.1 encoded material). With 5.1
encoded sources, a surround back channel will be
generated, but the material may sound better in the 5.1
format for which it was originally encoded (in which case, you
can simply switch surround back channel processing off).
• With a 7.1-channel surround system, audio signals that
have undergone matrix decoding processing through
surround back channel processing to which the Up Mix
function is added are output from the surround back
speakers.
Press
, then press SB CH repeatedly to cycle
the surround back channel options.
Each press cycles through the options as follows:
•
SB ON
– Matrix decoding processing for generating the
surround back component from the surround component
is turned on.
•
SB AUTO
– Matrix decoding processing for generating
the surround back component from the surround
component is switched automatically. Matrix decoding
processing is only performed when surround back
channel signals are detected in the input signals.
•
SB OFF
– Matrix decoding processing for generating the
surround back component from the surround component
is turned off.
Setting the Up Mix function
In a 7.1-channel surround system with surround speakers
placed directly at the sides of the listening position, the
surround sound of 5.1-channel sources is heard from the
side. The Up Mix function mixes the sound of the surround
speakers with the surround back speakers so that the
surround sound is heard from diagonally to the rear as it
should be.
• Using the Up Mix function is effective when the speakers
in the 7.1-channel surround system are set up as
recommended in the example on page 10.
• Depending on the positions of the speakers and the
sound source, in some cases it may not be possible to
achieve good results. In this case, set the setting to
OFF
.
1
Switch the receiver into standby.
2
While holding down PRESET
on the front panel, and
hold the
STANDBY/ON for about two seconds.
UP MIX: OFF
appears and the Up Mix function turns off. If
you want to turn this function on, perform steps 1 and 2
again.
• When set to
ON
, the (Up Mix) indicator on the front
panel lights.
Note
• Set to
ON
regardless of this setting when playing DTS-HD
signals.
• May automatically be set to
OFF
even when set to
ON
,
depending on the input signal and listening mode.
Setting the Audio options
There are a number of additional sound settings you can
make using the
AUDIO PARAMETER
menu. The defaults, if
not stated, are listed in bold.
Important
• Note that if a setting doesn’t appear in the
AUDIO
PARAMETER
menu, it is unavailable due to the current
source, settings and status of the receiver.
1
Press
, then press AUDIO PARAMETER button.
2
Use
/
to select the setting you want to adjust.
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3
Use
/
to set it as necessary.
See the table below for the options available for each setting.
4
Press RETURN to confirm and exit the menu.
INPUT SELECT
SOURCE
SLEEP
TV
CONTROL
INPUT
RECEIVER
RECEIVER
1
4
7
MIDNIGHT
2
5
8
SPEAKERS
LEV
SB CH
DISP
TEST TONE
3
6
9
CH
CH
CH SELECT
S
HDD
DVD
VCR
DTV/TV
RECEIVER
C
SW
L
R
SL
SR
SBL
SBR
SBL
SBR
C
SW
L
R
SL
SR
UP MIX OFF
UP MIX ON
Setting/What it does
Option(s)
S.DELAY
(Sound Delay)
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
0.0 to 9.0
(frames)
1 second = 25
frames (PAL)/30
frames (NTSC)
Default:
0.0
MIDNIGHT
/
LOUDNESS
a
The
MIDNIGHT
allows you to hear effective
surround sound of movies at low volumes.
The
LOUDNESS
is used to get good bass and
treble from music sources at low volumes.
M/L OFF
MIDNIGHT
LOUDNESS
INPUT SELECT
SOURCE
SLEEP
TV
CONTROL
INPUT
RECEIVER
RECEIVER
BD
DVD
TV
DTV/TV
ENTER
RETURN
AUDIO
PARAMETER
TUNER EDIT
TOOLS
MASTER
VOLUME
BAND
MENU
TOP
MENU
TUNE
TUNE
P
R
E
S
E
T
P
R
E
S
E
T
HOME
MENU
SETUP
RECEIVER
04_listening_your_system.fm 23 ページ ２０１１年７月２２日 金曜日 午後６時６分
