The System Setup menu
26
En
05
05
1
Use
/
to select ‘SP SETUP’ from the System Setup
menu, then press ENTER.
2
Use
/
to select ‘X.OVER’ from the SP SETUP menu,
then press ENTER.
3
Use
/
to select the frequency cutoff point.
Frequencies below the cutoff point will be sent to the
subwoofer (or
LARGE
speakers).
4
When you’re finished, press RETURN.
You return to the Speaker Setup menu.
Channel Level
Using the channel level settings, you can adjust the overall
balance of your speaker system, an important factor when
setting up a home theater system.
CAUTION
• The test tones used in the System Setup are output at
high volume.
1
Use
/
to select ‘SP SETUP’ from the System Setup
menu, then press ENTER.
2
Use
/
to select ‘CH LEVEL’ from the SP SETUP menu,
then press ENTER.
3
Use
/
to select a setup option.
•
T. TONE M
– Move the test tone manually from speaker
to speaker and adjust individual channel levels.
•
T. TONE A
– Adjust channel levels as the test tone moves
from speaker to speaker automatically.
4
Confirm your selected setup option.
The test tones will start after you press
ENTER
. After the
volume increases to the reference level, test tones will be
output.
5
Use
/
to adjust the level of each channel.
If you selected
T. TONE M
, use
/
to switch speakers. The
T. TONE A
setup outputs test tones in the following order
(depends on speaker settings):
L
C
R
SR
SBR
SBL
SL
SW
Adjust the level of each speaker as the test tone is emitted.
Note
• If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
• The subwoofer test tone is output at low volumes. You
may need to adjust the level after testing with an actual
soundtrack.
6
When you’re finished, press RETURN.
You return to the Speaker Setup menu.
Tip
• You can change the channel levels at any time by press
, then press
CH SELECT
and
LEV +/–
on the
remote control. You can also press
CH SELECT
and use
/
to select the channel, and then use
/
to adjust
the channel levels.
Speaker Distance
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
1
Use
/
to select ‘SP SETUP’ from the System Setup
menu, then press ENTER.
2
Use
/
to select ‘SP DISTN’ from the SP SETUP menu,
then press ENTER.
3
Use
/
to choose the speaker that you want then set
the distance.
Use
/
to adjust the distance of each speaker in 0.03 m
increments.
4
When you’re finished, press RETURN.
You return to the Speaker Setup menu.
The Auto Power Down menu
Set to automatically turn off the receiver after a specified time
has passed (when the power has been on with no operation
for several hours.
• Default setting:
OFF
1
Use
/
to select ‘APD’ from the System Setup menu,
then press ENTER.
2
Specify the amount of time to allow before the power
is turned off (when there has been no operation).
• Use
/
to select 2, 4 or 6 hours, or
OFF
(if no automatic
shutoff is desired).
3
When you’re finished, press RETURN.
You return to the System Setup menu.
The FL Demo Mode menu
Set whether or not various demos are to be shown on the
front panel display.
• Default setting:
ON
1
Use
/
to select ‘FL DEMO’ from the System Setup
menu, then press ENTER.
2
Use
/
to choose ON or OFF for the demo display.
3
When you’re finished, press RETURN.
You return to the System Setup menu.
RECEIVER
05_system_setup.fm 26 ページ ２０１１年９月１日 木曜日 午後８時１６分
