155
Integrator Mode
5.4.2 Example of Integrator Mode Operation
The basic operation in the menu mode is explained using
brightness adjustment as an example.
4
Press the [MENU] button on the remote control
unit or the main-control panel when ‘DISPLAY
CALL 2’ is displayed to open up the integrator
mode screen.
I N T E G R AT O R
I N P U T 1
ENTER
S C R E E N
S E T U P
O P T I O N
C O N T R A S T
B R I G H T N E S S
H . E N H A N C E
V . E N H A N C E
G AMMA
P I C T U R E R E S E T
W H I T E B A L A N C E
C O L O R D E T A I L
P I C T U R E
: 1 2 8
: 0
: 0
: 1 2 8
: 2 . 0
SET
EXIT
MENU
5
Press the [
5
/
∞
] buttons on the remote control
unit or the main-control panel to select
‘BRIGHTNESS’ then press the [SET] button.
I N T E G R AT O R
I N P U T 1
ENTER
S C R E E N
S E T U P
O P T I O N
P I C T U R E
SET
EXIT
MENU
: 2 . 0
: 1 2 8
: 0
: 0
: 1 2 8
C O N T R A S T
B R I G H T N E S S
H . E N H A N C E
V . E N H A N C E
G AMMA
P I C T U R E R E S E T
W H I T E B A L A N C E
C O L O R D E T A I L
6
Press the [
2
/
3
] buttons on the remote control
unit or the main-control panel to adjust to the
desired picture.
B R I G H T N E S S
:
SET
SET
EXIT
MENU
0
It is possible to move to other adjustment items
with the
5
/
∞
buttons.
7
Press the [SET] button on the remote control
unit or the main-control panel.
The adjusted value is saved in memory then
operation returns to the screen in step 5.
To continue with adjusting another item, repeat
steps 5 to 6.
8
When adjustment is complete, press the [MENU]
button on the remote control unit or the main-
control panel button to return to the normal
screen.
* The ID is shown to the side of the input display,
upper right area of the integrator mode screen
(See section 5.5.4, “ID Assigning” (pg. 195)).
STANDBY/ON
MENU
DISPLAY
/ SET
– VOL +
INPUT SCREEN SIZE
2
/
3
MENU DISPLAY
/ SET
5
/
∞
MENU
5
/
∞
SET
2
/
3
DISPLAY
Main-control panel
Remote control unit
1
Set the device to normal operation then press
the [INPUT] button to switch to the input to be
adjusted.
2
Press the [DISPLAY] button on the remote
control unit or the main-control panel to display
‘DISPLAY CALL 1’.
FULL
6 4 0
X
4 8 0
I N P U T 1
F H : 3 1 . 5 k H z
F V : 6 0 . 0 H z
P O L . H : N E G A
P O L . V : P O S I
3
Press the [DISPLAY] button on the remote
control unit or the main-control panel (3 seconds
or more) when ‘DISPLAY CALL 1’ is displayed to
display ‘DISPLAY CALL 2’.
T E M P E R AT U R E
H O U R M E T E R
O S D
B AU D R AT E
I N F O R M AT I O N
: A B C D E F G H I J K L M N
FA N C O N T R O L
I D N O. S E T
C O L O R M O D E
: + 2 5
: AU TO
: 9 6 0 0 B P S
: O N
: A L L
: N O R M A L
: 0 0 2 3 9 H
DAT E
: 0 0 1 A 0 0 1 X
L OT
: 0 0 1 A 0 0 1 K
S E R I A L N O.
: * * * * * * * * * * * * * * * *
P D P - 4 2 5 C M X / LV C 5
