94
PDP-433CMX
1
2
3
4
C
D
F
A
B
E
1
2
3
4
8.
FINAL SETUP: Factory preset values are set.
(See FINAL SETUP Details.)
9.
VIDEO STANDARD: The peak occurrences of STANDARD (USER MENU / POWER CONTROL) in the video system signal is set.
(Table 1 setting in the following table.) Note: Please do not change settings during service.
10. PC STANDARD: The peak occurrences of STANDARD (USER MENU / POWER CONTROL) in the PC system signal is set.
(Table 2 setting in the following table.) Note: Please do not change settings during service.
11. VIDEO MODE1: The peak occurrences of MODE1 (USER MENU / POWER CONTROL) in the video system signal is set.
(Table 3 setting in the following table.) Note: Please do not change settings during service.
12. PC MODE1: The peak occurrences of MODE1 (USER MENU / POWER CONTROL) in the PC system signal is set.
(Table 4 setting in the following table.) Note: Please do not change settings during service.
13. EEP DATA READ: Data on each address of the EEPROM are displayed.
14. MASK1: To select the full mask.
Note: The last setting for either MASK 1 or MASK 2 is stored in memory.
15. MASK2: To select the mask pattern.
Note: The last setting for either MASK 1 or MASK 2 is stored in memory.
Notes on MASK 1 and MASK 2
• When any key is pressed, an OSD is displayed for two seconds, and during this period the full mask signal output is stopped.
• When the full mask is selected on the MASK selection menu, two seconds after the full mask is selected (with no key pressed during this
period,) the displayed OSD disappears, then full mask is displayed in turn.
• To release the mask setting, use "M00" of RS-232C Factory Adjustment mode or "MASK OFF" of Service Factory menu.
(The mask setting cannot be released with FULL MASK OFF of the Integrator menu or "FMN" of the RS-232C Factory Adjustment mode.)
VIDEO
Current Input Signal
PL6 (fixed)
PC
Table1
Table2
Table3
STANDARD mode
MODE1
MODE2
POWER CONTROL
setting
Table4
: To select a digit (four digits) of an address
5∞
: To select numbers
SET : To shift to the next higher layer
Displayed data for each address are updated each time
the address is changed.
Display color : White (Selected address is yellow)
Half tone
: Blue (second line / 15th line for
each 1st to 32th columns)
: To select YES or NO
SET
: When YES is selected, the SET DATA are stored
in memory, and the initial display appears.
When NO is selected, NOW DATA is
maintained, and the initial display appears.
I N I T
P
N O
Y E S
U L S
M
E
E T
R
E
S E T
?
–
–
S 1
I N 4 – 0 2 –
∗
2
N T
# 1
I N I T
E E P
D A T A
R E A D
0
8
-
F
F
0
1
:
–
–
S 1
I N 4 – 0 2 –
∗
2
N T
# 1
1
5
10
15
16
1
5
10
15
20
25
30
32
1
5
10
15
16
1
5
10
15
20
25
30
32
Summary of Contents for PDP 433CMX
