PDP-501MX, PDP-V501X
43
Keys
1
SUB CONTRAST (000 to 127)
2
ACL START
(000 to 015)
3
ACL GAIN
(000 to 015)
9
ACL SW
ACL SW ON/OFF cyclic
p
VAP GAIN
(000 to 007)
q
VAP INV
(000 to 031)
BS3
R SIDE LEV
(000 to 255)
BS5
G SIDE LEV
(000 to 255)
BS7
B SIDE LEV
(000 to 255)
BS11 R FULL LEV
(000/255)
BS13 G FULL LEV
(000/255)
BS15 B FULL LEV
(000/255)
Note: Do not change the factory settings for keys
6
and
8
.
If changed, the panel may be damaged.
Increases the value of the parameter selected for
adjustment
Volume –
Decreases the value of the parameter selected for
adjustment
Set
Memorizes the adjusted value and moves to a
higher level
Keys
Commands
1
SUB VIDEO (Set using the SET key.)
2
MIRROR_MODE (Inverted Picture mode)
OFF/XY cyclic (OFF at the factory setting) <MMN>/<MMZ>
3
FULL MASK
ON/OFF-cyclic (OFF at the factory setting) <FMY>/<FMN>
5
HOUR METER (Displays the current hours meter) <HMD>
6
BAUD RATE (Sets the RS-232C communication speed with
PC)
<BRm> *
1200 to 19200 cyclic (4800) at the factory setting
7
EEPROM INIT. (For manufacturing line only)
8
MASK CONTROL (Automatic mask position change setting)
ON/OFF cyclic (ON at the factory setting) <MCY>/<MCN>
p
STD-RGB (Standard speed (15. 734kHz) RGB enable setting)
ON/OFF (OFF at the factory setting)
<NRY>/<NRN>
q
INTE. MODE (Integrator mode setting)
FREE, ON, LOCK cyclic (FREE at the factory setting)
(Menu OFF)
<IMF>/<IMY>/<IMN>
BS1 FINAL SETUP (factory setting) Set using the Set key
(Recovers the initial setting) Refer to next page. <FST>
BS3 IPQ ADJ (Progressive conversion
parameter adjustment)
Set (
1
, BS1 )
Sets the mode and moves to the lower level.
Note: 1) Do not change the factory settings for the modes of keys
9
. If changed, the panel may be damaged.
2) Be sure to turn the key
3
FULL MASK off when the power
is turned off.
5. INITIALIZE ( Bilingual key)
Mode for changing and checking the initial settings.
(1) Menu in mode
INITIALIZE
MODE E A /
Current main menu
SUB VIDEO
Current selected menu
SUB VIDEO
MODE E A /
Current selected mode
SUB CONTRAST
Setting parameter
: 127
Adjustment value
(2) Parameter adjustments (SUB VIDEO)
Common picture quality adjustment for all input signal modes.
Not necessary to readjust
Fix at the factory setting
Not necessary
to readjust
F i x a t t h e
factory
setting
3
m: 1~5
1
→
1200bps
2
→
2400bps
3
→
4800bps
4
→
9600bps
5
→
19200bps
*
Summary of Contents for PDP-501MX
Page 16: ...PDP 501MX PDP V501X 16 A B C D 1 2 3 4 1 2 3 4 3 3 POWER SUPPLY MODULE 1 2 J 1 2 ...
Page 17: ...PDP 501MX PDP V501X 17 A B C D 5 6 7 8 5 6 7 8 J 1 2 ...
Page 18: ...PDP 501MX PDP V501X 18 A B C D 1 2 3 4 1 2 3 4 3 4 POWER SUPPLY MODULE 2 2 J 2 2 ...
Page 19: ...PDP 501MX PDP V501X 19 A B C D 5 6 7 8 5 6 7 8 J 2 2 ...
