I
NST
ALLA
TION
AND
C
ONNECTIONS
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
E
E
NGLISH
NGLISH
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
<ARE1349> En
9
I
NSTALLATION
AND
C
ONNECTIONS
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Installation of the unit
Installation using the optional PIONEER stand or
installation bracket
÷
Please be sure to request installation or mounting of this unit
or the installation bracket by an installation specialist or the
dealer where purchased.
÷
When installing, be sure to use the bolts provided with the
stand or installation bracket.
÷
For details concerning installation, please refer to the
instruction manual provided with the stand or installation
bracket.
Installation using accessories other than the
PIONEER stand or installation bracket (sold
separately)
÷
When possible, please install using parts and accessories
manufactured by PIONEER. PIONEER will not he held
responsible for accident or damage caused by the use of parts
and accessories manufactured by other companies.
÷
For custom installation, please consult the dealer where the
unit was purchased, or a qualified installer.
Wall-mount installation of the unit
This unit has been designed with bolt holes for
wall-mount installation, etc.. The installation holes that
can be used are shown in the diagram below. (Caps can
be removed by turning with a screwdriver, coin, or similar
tool.)
÷
Be sure to attach in 4 or more locations above and
below, left and right of the center line.
÷
Use bolts that are long enough to be inserted 1/2 inch
(12 mm) to 13/16 inch (20 mm) into the main unit from
the attaching surface for both a holes and b holes.
Refer to the side view diagram below.
÷
As this unit is constructed with glass, be sure to install
it on a flat, unwarped surface.
CAUTION
Because this unit weighs about 94 lbs 13 oz (about 43 kg) and
has little depth making it unstable, please use 2 people or more
when packing, carrying or installing.
CAUTION
This unit incorporates a thin design. To ensure safety if vibrated
or shaken, please be sure to take measures to prevent the unit
from tipping over.
CAUTION
To avoid malfunction, overheating of this unit, and possible fire
hazard, make sure that the vents on the main unit are not
blocked when installing. Also, as hot air is expelled from the
vents, be careful of deterioration and dirt build up on rear surface
wall, etc..
CAUTION
Please be sure to use an M8 (Pitch = 1.25 mm) bolt. (Only this
size bolt can be used.)
b hole
Main unit
b hole
Center line
b hole
b hole
b hole
b hole
Center line
a hole
b hole
Bolt
Bolt
Attaching surface
Installation
bracket, etc..
1/2 inch (12 mm) to
13/16 inch (20 mm)
1/2 inch (12 mm) to
13/16 inch (20 mm)
Rear view diagram
Side view diagram
a hole
a hole
Vents (fan)
