background image

Installation

<ENGLISH>

Switching the DSP setting mode

This product features two operation modes: the 3-way network mode (NW) and the standard
mode (STD). You can switch between modes as desired. Initially, the DSP setting is set to
the standard mode (STD).
• After switching, reset the microprocessor. (Refer to operation manual.)

• Use a thin standard tip screwdriver to switch the DSP switch on the bottom of this

product.

Fig. 12

About the fixing screws for the front panel

If you do not operate the removing and attaching the front panel function, use the supplied
fixing screws to fix the front panel to this unit.

Fig. 13

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 9)

Fig. 9

2. Fastening the unit to the factory radio mounting bracket. 

(Fig. 10) (Fig. 11)

Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
binding screws (5 

×

6 mm) or flush surface screws 

(5 

×

6 mm), depending on the shape of the screw holes in

the bracket

.

Fig. 10

Fig.11

Frame

Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)

Screw

Dashboard or Console

Factory radio mounting bracket

Fixing screws

Summary of Contents for Premier DEH-P960MP







Reviews: