PRV-LX10
142
1
2
3
4
1
2
3
4
C
D
F
A
B
E
4) Data on the Encoder board (Page 4)
The data on the Encoder board are displayed. If the [SIDE-A] key is pressed on this page, the error log for the Encoder
board can be checked.
An error record is expressed as shown below:
(Example) 2003/07/01 10:30:20 == 09 03 ==
Error code (last 2 digits)
Task ID (used in some error codes)
Date and time of occurrence
The meaning of the error codes and correction measures are described below:
Code
Content of Error
Correction Measures
01
Data Read Timeout Error
Turn the power off then on again.
02
Copy Protection Error
As the selected input signal is copy-protected, recording could not be performed.
When this error is generated even if the video signal from the disc created by the PRV-LX1
is to be recorded, replace the AVIB board.
03
(task ID : 09(h))Illegal frame number Error Turn the power off then on again.
(task ID : 32(h))No digital signal Error
Because no digital signal is input to the selected digital input connectors, recording could not
be performed. When this error is generated even if the digital signal is confirmed to be input
to the DV connectors, etc., replace the AVIB board.
04
PCI Destination Address Timeout Error Turn the power off then on again.
05
PCI Map Timeout Error
Turn the power off then on again.
C9
Hard Error
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
CA
Reset Error
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
(task ID : 0A(hex))Stream Buffer Full Error Turn the power off then on again.
CB
Initialize Error
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
CC
Standby Error
Turn the power off then on again.
CD
Command Error
Turn the power off then on again.
CE
Stream Timeout Error
Turn the power off then on again.
CF
Command Timeout Error
Turn the power off then on again.
D0
Buffer Full Error
Turn the power off then on again.
D2
Hard Error(Audio Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
D3
Reset Error(Audio Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
D4
Initialize Error(Audio Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
D5
Standby Error (Audio Enc.)
Turn the power off then on again.
D6
Command Error (Audio Enc.)
Turn the power off then on again.
D7
Command Timeout Error (Audio Enc.)
Turn the power off then on again.
DC
Hard Error (Video Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
DD
Reset Error (Video Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
DE
Initialize Error (Video Enc.)
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
DF
Standby Error (Video Enc.)
Turn the power off then on again.
E0
Command Error (Video Enc.)
Turn the power off then on again.
E1
DV Decode Error
Turn the power off then on again.
E2
DV Encode Error
Turn the power off then on again.
E3
FS Change Error (before)
Turn the power off then on again.
E4
FS Change Error (after)
Turn the power off then on again.
E5
Command Timeout Error (Video Enc.)
Turn the power off then on again.
E6
Command Execute Error (Video Enc.)
Turn the power off then on again.
5) Recording data (Page 5)
The internal data on recording are displayed.
6) Application data (Page 6)
The internal data on the application are displayed.
Note on the drive error log: The drive error log can be displayed in Test mode.
