background image

ORDER NO.

PIONEER CORPORATION

   4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC.

  P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.

PIONEER EUROPE NV

  Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

  253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2006

T – ZZS  FEB. 2006 Printed  in Japan

SPEAKER SYSTEM

S-1EX

 XTW/E

RRV3337

CONTENTS

1. PARTS LIST .................................................................................. 2

2. FOR PRECAUTION OF REASSEMBLY AND DISASSEMBLY .... 8

3. SCHEMATIC DIAGRAM ............................................................. 11

4. JIG ............................................................................................... 12

NOTE

As this speaker system weighs approx. 66 kg, be sure to have two people work on it. If this
speaker system will be turned on its side for servicing, lay it on a piece of soft cloth, etc., to
protect the cabinet from being scratched.

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to
properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the
warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk
trying to do so and refer the repair to a qualified service technician.

WARNING

This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of  California to
cause cancer, birth defects or other reproductive harm.

Health & Safety Code Section 25249.6  – Proposition 65

Summary of Contents for S-1EX













Reviews: