Pioneer ]S-2EX Service Manual Download

Page: 5 / 10

S-2EX

2. FOR PRECAUTION OF REASSEMBLY AND DISASSEMBLY

2.1 GRILLE

How to disassemble

Loosen the finishing screws. Then remove the grille.

Note 1:

You may remove the fastening screws if they impede
disassembly.

How to reassemble

Finishing Screws

Finishing
Screws

Place the grille with the badge located at the lower part,
aligning the 4 holes of the grille with the fastening screws
inserted in Step

Tighten the supplied finishing screws into the fastening
screws to secure the grille.

Note 2:

Do not use a flathead screwdriver or a hexagonal wrench to
tighten the screws. Securing the screws too tightly may
damage the cabinet.

Insert the supplied fastening screws (upper: long, lower:
short) into the screw holes at the four corners of the
speaker front.

Fastening
Screws
(long)

Fastening
Screws
(short)

∅

8.5

(4.6)

Screw (SBA1225)

∅

8.3

2.5

4.2 max.

Screw (SBA1260)

4.2 max.

∅

8.3

∅

2.5

4.2 max.

Screw (SBA1261)

Summary of Contents for ]S-2EX











Search results

Summary of Contents for ]S-2EX

Reviews:

Related manuals for ]S-2EX

Brands by name

Popular brands

Pioneer ]S-2EX, Service Manual

Search results

Summary of Contents for ]S-2EX

Reviews:

Related manuals for ]S-2EX

Brands by name

Popular brands