DIN Rear-mount
Installation using the screw holes on
the side of the unit
• Fastening the unit to the factory
radio mounting bracket. (Fig. 13)
(Fig. 14) (Fig. 15)
Select a position where the screw holes
of the bracket and the screw holes of
this product become aligned (are fitted),
and tighten the screws at 2 places on
each side. Use any of binding screws (4
×
3 mm), binding screws (5
×
6 mm) or
flush surface screws (5
×
6 mm),
depending on the shape of the screw
holes in the bracket.
*1 Use binding screws (4
×
3 mm) only.
Fig. 13
• When installing in a shallow space,
use the following screw holes. In this
case, stick conceal tape on parts that
protrude from the dashboard.
Fig. 14
Fig. 15
Screw
Dashboard or
Console
Factory radio mounting
bracket
*1
*1
Conceal tape
*1
*1
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver’s
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• Do not place the display in a position where it will
impede the driver’s visibility or affect the opera-
tion of your vehicle’s air bags.
• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 7)
Fig. 7
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 8)
Fig. 8
•
When mounting the hide-away unit, make sure
none of the leads are trapped between the hide-
away unit and the surrounding metalwork or fit-
tings.
•
Do not mount the hide-away unit near the heater
outlet, where it would be affected by heat, or near
the doors, where rainwater might splash onto it.
•
If the hide-away unit is installed in the passenger
compartment, anchor it securely so it does not
break free while the car is moving, and cause
injury or an accident.
•
If the hide-away unit is installed under a front
seat, make sure it does not obstruct seat move-
ment. Route all leads and cords carefully around
the sliding mechanism so they do not get caught
or pinched in the mechanism and cause a short
circuit.
Installing the hide-away unit
• Install the hide-away unit with
the velcro tape. (Fig. 9)
• Thoroughly wipe off the surface
before affixing the velcro tape.
• Direct installation on the carpet is
possible if the hard velcro tape will
adhere to the carpet. Do not use the
soft velcro tape in this case.
Fig. 9
Velcro tape
(hard)
Car mat or chassis
Velcro tape
(soft)
Hide-away unit
Do not close this area.
30
°
DIN Front/Rear-mount
This unit can be properly installed
either from “Front” (conventional DIN
Front-mount) or “Rear” (DIN Rear-
mount installation, utilizing threaded
screw holes at the sides of unit chassis).
For details, refer to the following illus-
trated installation methods.
Before installing the unit
• Remove the frame and the hold-
er. (Fig. 10)
Pull out to remove the frame and then
loosen the screws (2
×
3 mm) to
remove the holder. (When reattaching
the frame, point the side with a groove
downwards and attach it.)
Fig. 10
DIN Front-mount
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 11)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
Fig. 11
2. Install the unit into the dash-
board. (Fig. 12)
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
• After installing the unit into the dash-
board, reattach the frame.
Fig. 12
Rubber bush
Screw
Dashboard
Side bracket
Screw (2
×
3 mm)
182
53
Holder
Conceal tape
Side bracket
Flush surface screw (5
×
6 mm)
Holder
Frame
Screw (2
×
3 mm)
Installation
<ENGLISH>