DRB1508-C
En
15
English
15
14
Tempo control section
Adjust the track playing speed here (page 20).
When [
BPM LOCK
] is used, the playing speeds of two tracks can be
matched easily (page 21).
o
BPM LOCK
p
TEMPO RANGE
q
MASTER TEMPO
r
TEMPO
Front panel
s
t
s
Disc force eject pin insertion hole (page 15)
t
Disc insertion slot (page 15)
Main unit display
A.CUE
LOCK
16
REMAIN
M
S
F
TEMPO
%
INFO
BROWSE
BPM
1
a
c
b
2
3
4
5
6
7
8
9
1
Track number
This displays the track number.
It is not possible to display more than 100 tracks.
2
A. CUE (page 17)
This lights when auto cue is set.
3
Playing address display
The track is displayed as a bar graph.
Turns off from the left side when the remaining time is displayed. The
entire graph flashes slowly when the remaining track time is under 30
seconds, then flashes quickly when the remaining track time is under
15 seconds.
4
INFO (page 19)
5
BROWSE (page 19)
6
REMAIN
This lights when the time display is set to the remaining time.
7
M, S, F (time display)
“M” indicates minutes, “S” seconds, “F” frames.
There are 75 frames to a second.
8
LOCK (page 21)
This lights when the BPM is locked.
9
TEMPO %
This indicates the percentage by which the playing speed is changed.
a
WIDE, ±16, ±10, ±6
This indicates the range by which the playing speed can be adjusted.
b
BPM
Displays BPM (Beats Per Minute) of the track currently being played.
c
Information display section
Up to 13 characters can be displayed for each. The characters that
can be displayed are letters A to Z, numbers 0 to 9 and certain sym-
bols. “?” is displayed for other characters.
Setting the source to be played
(source select section)
s
t
USB
STOP
SOURCE SELECT
MP3/AAC
WAV/AIFF
PLAYLIST
BPM
DISC
LOCK
BACK
SELECT PUSH
TIME MODE
AUTO CUE
DISPLAY
UTILITY
3
4
5
6
7
Loading discs
!
Set the disc with the printed side facing up.
!
Insert the disc horizontally into the disc insertion slot in the main
unit’s front panel.
!
Do not load more than 1 disc.
!
Do not force discs into the set’s disc insertion slot when the set’s
power is off. Doing so could damage the disc or the set.
!
When the disc is being drawn in or ejected, do not apply any force
to the disc in the direction opposite its movement. Doing so could
damage the disc or the set.
1 Press [
u
]
1
.
Turn on the power of this unit.
2 Insert the disc into the disc insertion slot
t
.
Playback starts.
!
When auto cue is turned on, playback starts when
[
PLAY/PAUSE
f
] is pressed. For details on the auto cue function,
see
Setting auto cue
on page 17.
Ejecting discs
Press [
h
DISC]
2
.
The disc is ejected from the disc insertion slot.
!
If you press [
h
DISC
] by mistake, press [
PLAY/PAUSE
f
] immedi-
ately to restore this unit to the status it was in just before [
h
DISC
]
was pressed. (No sound is output during this time.)
About ejecting discs by force
!
If the disc is not ejected when [
h
DISC
] is pressed, eject the disc
forcibly by inserting the disc force eject pin into the disc force eject
pin insertion hole.
!
When forcibly ejecting a disc, be sure to do so following the proce-
dure below.
