DRB1508-C
En
25
English
25
24
List of MIDI Messages
SW Name
SW Type
MIDI Messages
(3 Bytes)
Notes
Jog dial
(scratch)
General
Purpose
Controller
Bn
10
dd
Linear value with
respect to speed from
stop to x4 speed. Stop:
40, FWD (CW) direc-
tion: 41 to 7F (x0.06 to
x4 speed), REV (CCW)
direction: 3F to 00 (x0.5
to x4 speed)
TEMPO
VR
Bn
1D
dd
00 to 7F (00 at – side, 7F
at + side, 40 at center)
Jog dial (spin
outer section)
General
Purpose
Controller
Bn
30
dd
Linear value with
respect to speed from
x0.5 speed to x4 speed.
Stop (under x0.49
speed): 40, FWD (CW)
direction: 41 to 7F
(x0.5 to x4 speed), REV
(CCW) direction: 3F to
00 (x0.5 to x4 speed)
SELECT PUSH
(turn)
General
Purpose
Controller
Bn
4F
dd
98 – 127, 1 – 30 Differ-
ence of count from
previous time is sent
(±1 – ±30) When over
±30, set at ±30
PLAY/
PAUSE
f
SW
9n
00
dd
OFF=00, ON=7F
CUE
SW
9n
01
dd
OFF=00, ON=7F
SEARCH
n
SW
9n
02
dd
OFF=00, ON=7F
SEARCH
m
SW
9n
03
dd
OFF=00, ON=7F
TRACK
SEARCH
p
SW
9n
04
dd
OFF=00, ON=7F
TRACK
SEARCH
o
SW
9n
05
dd
OFF=00, ON=7F
LOOP IN
/
CUE
(
HOT LOOP
)
SW
9n
06
dd
OFF=00, ON=7F
LOOP OUT
(
OUT ADJUST
)
SW
9n
07
dd
OFF=00, ON=7F
RELOOP/
EXIT
SW
9n
08
dd
OFF=00, ON=7F
TIME MODE
(
AUTO CUE
)
SW
9n
0E
dd
OFF=00, ON=7F
DISPLAY
(
UTIL-
ITY
)
SW
9n
0F
dd
OFF=00, ON=7F
TEMPO RANGE
SW
9n
10
dd
OFF=00, ON=7F
MASTER
TEMPO
SW
9n
11
dd
OFF=00, ON=7F
VINYL MODE
SW
9n
12
dd
OFF=00, ON=7F
BEAT LOOP
(
LOOP DIVIDE
)
+
SW
9n
16
dd
OFF=00, ON=7F
BEAT LOOP
(
LOOP DIVIDE
)
–
SW
9n
17
dd
OFF=00, ON=7F
Jog dial (press
top)
SW
9n
20
dd
OFF=00, ON=7F
BPM LOCK
SW
9n
26
dd
OFF=00, ON=7F
PLAYLIST
SW
9n
2E
dd
OFF=00, ON=7F
h
DISC
SW
9n
2F
dd
OFF=00, ON=7F
BACK
SW
9n
32
dd
OFF=00, ON=7F
SELECT PUSH
(press)
SW
9n
33
dd
OFF=00, ON=7F
n is the channel number.
Cautions on use
About condensation
Water droplets (condensation) may form inside the unit (on operating
parts and lenses) in the winter, for example, if the unit is moved from a
cold place into a warm room or if the temperature in the room in which
the unit is installed rises suddenly (through heating, etc.). The unit
will not operate properly and will not be playable with condensation
inside. Let the unit stand for 1 to 2 hours at room temperature (though
this time depends on the conditions of the condensation) without
turning on the power. The water droplets will evaporate and the unit
will become playable. Condensation can occur in the summer as well
if the unit is exposed to the direct wind from an air-conditioner, etc. If
this happens, move the unit to a different location.
Cleaning the lens
The player’s lens should not become dirty in normal use, but if for
some reason it should malfunction due to dust or dirt, consult your
nearest Pioneer authorized service center. Although lens cleaners
for players are commercially available, we advise against using them
since some may damage the lens.
Handling discs
Storing
!
Always place discs in their cases and store them vertically, avoid-
ing hot, humid places, places exposed to direct sunlight and
extremely cold places.
!
Be sure to read the cautions included with the disc.
Cleaning discs
!
Discs may not play if there are fingerprints or dust on them. In this
case, use a cleaning cloth, etc., to gently wipe the disc from the
inside towards the outside. Do not use dirty cleaning cloths.
!
Do not use benzene, thinner or other volatile chemicals. Also do
not use record spray or antistatic agents.
!
For tough dirt, apply some water to a soft cloth, wring out thor-
oughly, wipe off the dirt, then wipe off the moisture with a dry
cloth.
!
Do not use damaged (cracked or warped) discs.
!
Do not let the signal surface of discs get scratched or dirty.
!
Do not place two discs in the disc tray, one on top of the other.
!
Do not attach pieces of paper or stickers to discs. Doing so could
warp discs, making it impossible to play them. Also note that
rental discs often have labels attached to them, and the label’s
glue may have oozed out. Check that there is no glue around the
edges of such labels before using rented discs.
