background image

25

En

03

Switching the output 
video resolution

Use the procedure below to switch the output 
video resolution from the various video output 
terminals. 

Press RESOLUTION 

e

/

r

.

• The current output video resolution setting is 

displayed on the player’s front panel display.
To switch the output video resolution, press 

RESOLUTION 

e

/

r

 again.

• The output video resolution setting can also be 

switched by selecting 

Resolution

 from the 

Initial Setup

 menu (page 39).

 Caution

• On some devices (TV, AV receiver or amplifier, 

etc.), the video or audio may not be output 
properly when the resolution is switched. If this 
happens, use 

RESOLUTION

 to set a resolution 

at which the video and audio are properly 
output.

• When video signals are being output with a 

resolution of 4K/24p, 4K, 1080/50i, 1080/50p, 
720/50p, 1080/24p, 1080/60i, 1080/60p or 
720/60p from the 

HDMI OUT

 terminals, the 

picture may be output with an aspect ratio of 
16:9, even if the 

TV Screen

 is set to 

4:3 

(Standard)

.

• The picture may not be displayed for a while 

when the resolution is switched.

• When the connected device supports 3D and if 

a 3D Disc is played back, the 3D output is 
prioritized for output, regardless of the 
resolution settings. Also, switching of 
resolution may not be possible while the 3D 
contents are playing.

• When 

Auto

 is selected, the picture is output at 

60 frames/second if your TV is not compatible 
with 1080/24p signals.

• When 

4K

4K/24p

1080/24p

 or 

Source Direct

 is 

selected, the signals are output as such, even if 
your TV is not compatible with 4K, 4K/24p or 
1080/24p signals. If the picture is not displayed 
properly, use 

RESOLUTION

 

e

/

r

 to set an 

output video resolution at which the video and 
audio signals are properly output.

• When the 

Resolution

 is set to 

Auto

 and if the 

television set in use supports 4K or 4K/24p 
output, then the output is made in 4K or 4K/
24p. If the connected television set does not 
support 4K or 4K/24p, then the output is made 
with a recommended resolution other than 4K.

• When the 

Resolution

 is set to 

Auto

1080p

4K

 or 

4K/24p

 and if the resolution of output from the 

HDMI is 1080p, 4K or 4K/24p, then output may 
not occur depending on the HDMI cable in use.

• There are resolutions that cannot be output 

depending on the television set in use.

• When the 

HDMI Mode

 is set to 

Pure Audio

, the 

1080p60, 4K/60p or 4K/24p, output will not 
occur even if the resolution is set to 

Auto

 or 

1080p

4K

 or 

4K/24p

. The output will be 

delivered with a resolution of 1080/60i, 1080/
24p or the like, depending on the resolution of 
the source and the connected television set.

• For Dolby Vision output, the optimal resolution 

is automatically set for video content.

• When playing an UHD-BD disc, if the 

connected HDMI device does not support 
HDCP 2.2, the video cannot be output in 4K or 
4K24p resolution even if 

Auto

4K24p

4K

 or 

Source Direct

 is selected. Also, depending on 

the HDMI device, the HDMI or HDCP setting 
may be required. Check the operating 
instructions of the connected device.

Summary of Contents for UDP-LX800

































































Reviews: