3
3
19
Chapter
Basic playback
Playing a source
Here are the basic instructions for playing a source (such as
a DVD disc) with your home theater system.
1
Switch on your system components and receiver.
Start by switching on the playback component (for
example a DVD player), your TV and subwoofer (if you
have one), then the receiver (press
RECEIVER
).
2
Switch the TV input to the input that connects this
receiver.
For example, if you connected this receiver to the
VIDEO
jacks on your TV, make sure that the
VIDEO
input is now
selected.
3
Press input function buttons to select the input function
you want to play.
•
The input of the receiver will switch over, and you will
be able to operate other components using the remote
control. To operate the receiver, first press
on the remote control, then press the appropriate
button to operate.
•
The input source can also be selected by using
INPUT
SELECT
buttons on the remote control, or by
using the front panel
INPUT SELECTOR
dial. In this
case, the remote control won’t switch operational
modes.
If you selected the proper input source and there is still
no sound, select the audio input signal for playback (see
Selecting the audio input signal
).
4
Press
AUTO/DIRECT
to select ‘AUTO SURROUND’ and
start playback of the source.
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, with a digital audio connection, you should
hear surround sound. If you’re playing a stereo source or
if the connection is an analog audio connection, you will
only hear sound from the front left/right speakers in the
default listening mode.
It is possible to check on the front panel display whether
or not surround sound playback is being performed
properly.
If the display does not correspond to the input signal and
listening mode, check the connections and settings.
Note
•
You may need to check the digital audio output settings on
your DVD player or digital satellite receiver. It should be set
to output Dolby Digital, DTS and 88.2 kHz/96 kHz PCM (2
channel) audio, and if there is an MPEG audio option, set
this to convert the MPEG audio to PCM.
•
Depending on your DVD player or source discs, you may
only get digital 2 channel stereo and analog sound. In this
case, the receiver must be set to a multichannel listening
mode if you want multichannel surround sound.
5
Use
/–
to adjust the volume level.
Turn down the volume of your TV so that all sound is
coming from the speakers connected to this receiver.
Selecting the audio input signal
The audio input signal can be selected for each input source.
Once it is set, the audio input that was selected will be applied
whenever you select the input source using the input function
buttons.
Press
SIGNAL SEL
to select the audio input signal
corresponding to the source component.
Each press cycles through the following:
•
H
– Selects an HDMI signal.
H
can be selected for
BD
,
DVD
,
SAT/CBL
or
GAME
input. For other inputs,
H
cannot be selected.
-
When the
HDMI
option in
is set to
THRU
, the sound will be heard
through your TV, not from this receiver.
•
A
– Selects the analog inputs.
•
C1
/
O1
– Selects the digital input. The coaxial 1 input is
selected for
C1
, and the optical 1 audio input is
selected for
O1
.
When
H
(HDMI) or
C1
/
O1
(digital) is selected and the
selected audio input is not provided,
A
(analog) is
automatically selected.
Note
•
BD
and
GAME
inputs are fixed to
H
(HDMI). It cannot be
changed.
•
For the
TV
input, only
A
(analog) or
C1
/
O1
(digital) can be
selected. However, if the
ARC
at
HDMI Setup
is set to
ON
,
the input is fixed to
H
(HDMI) and cannot be changed.
•
When set to
H
(HDMI) or
C1
/
O1
(digital),
lights when a
Dolby Digital signal is input, and
DTS
lights when a DTS
signal is input.
•
When the
H
(HDMI) is selected, the
A
and
DIGITAL
indicators are off (see
).
•
When digital input (optical or coaxial) is selected, this
receiver can only play back Dolby Digital, PCM (32 kHz to
96 kHz) and DTS (including DTS 96 kHz/24 bit) digital signal
formats. The compatible signals via the HDMI terminals
are: Dolby Digital, DTS, SACD (DSD 2 ch only), PCM
(32 kHz to 192 kHz sampling frequencies), Dolby TrueHD,
Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio
and DVD Audio (including 192 kHz). With other digital
signal formats, set to
A
(analog).
•
You may get digital noise when a LD or CD player
compatible with DTS is playing an analog signal. To prevent
noise, make the proper digital connections (
) and
set the signal input to
C1
/
O1
(digital).
RECEIVER
Summary of Contents for VSX-530-K
Page 48: ......
