Using the tuner
08
25
En
English
Français
Español
Chapter 8:
Using the tuner
Listening to the radio broadcasts
The following steps show you how to tune in to FM and DAB+
radio broadcasts using the automatic (search) and manual
(step) tuning functions. Once you are tuned to a station you
can memorize the frequency for recall later. See
Saving
station presets
below for more on how to do this.
Tuning
1
Press the
STANDBY/ON to turn the power
on.
2
Press TUNER repeatedly to select desired
frequency band (FM or DAB+).
3
Press TUNE +/– on the remote control to
tune in to the desired station.
Automatic tuning:
Press and hold
TUNE +/–
, scanning will start automatically
and the tuner will stop at the first receivable broadcast
station.
Manual tuning:
Press the
TUNE +/–
repeatedly to tune in to the desired
station.
Note
• When radio interference occurs, automatic tuning may
stop automatically at that point.
• Automatic tuning will skip weak signal stations.
• To stop the automatic tuning, press
.
• When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first. Finally, the station
name will appear.
• Full auto tuning can be achieved for RDS stations using
Auto Station Program Memory (ASPM) mode, see
page 27.
To receive an FM stereo transmission:
Press
ST/MONO
to select stereo mode and “AUTO” will be
displayed.
Improving poor FM reception:
1
Press ST/MONO repeatedly to select MONO.
This will change the tuner from stereo to mono and usually
improve the reception.
Saving station presets
If you often listen to a particular radio station, it’s convenient
to have the receiver store the frequency for easy recall
whenever you want to listen to that station (Preset tuning).
This saves the effort of manually tuning in each time. This unit
can memorize up to 40 stations.
(FM 30 stations/DAB 10 stations)
1
Tune to a station you want to memorize.
See
Tuning
above for more on this.
2
Press MEMORY/PROGRAM.
The preset number will flash.
3
Press /– to select the preset
channel number.
4
Press MEMORY/PROGRAM to store that
station in memory.
If the preset number has changed from flashing to lighting,
before the station is memorised, repeat the operation from
step 2.
• Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note
• The backup function protects the memorised stations for
a few hours should there be a power failure or the AC
power cord become disconnected.
STANDBY/ON
CD
USB
TUNER
AUDIO IN
iPod
DISPLAY
FOLDER
TUNE+
1
2
3
4
5
6
7
8
9
0
BT AUDIO
CLOCK/TIMER
SLEEP
EQUALIZER
P.BASS
BASS/TREBLE
RANDOM
CLEAR
REPEAT
OPEN/CLOSE
DISPLAY
FOLDER
MENU
PRESET
VOLUME
ST/MONO
ASPM
PTY
DISPLAY
+
MUTE
TUNE–
TUNE+
DIMMER
–
+
–
MEMORY
/PROGRAM
RDS
ENTER
DISPLAY
FOLDER
MENU
PRESET
VOLUME
+
MUTE
TUNE–
TUNE+
DIMMER
–
+
–
MEMORY
/PROGRAM
0
ENTER
DISPLAY
FOLDER
MENU
PRESET
VOLUME
+
MUTE
TUNE–
TUNE+
–
+
–
MEMORY
/PROGRAM
0
RANDOM
CLEAR
REPEAT
ENTER
X-CM32_VXE8_En.book 25 ページ ２０１４年３月１２日 水曜日 午後２時５２分
