To replace grommets or eyelets, pull the conductor through the shielding sufficiently to make eyelet
accessible. Remove the eyelet being careful not to damage conductor wire. Replace grommet and eyelet
using the “AB” groove of Crimping Tool No. 11-4152 or a pair of diagonal pliers modified as shown in
Figure 22. Work the wire back into the shielding so the grommet fits properly against the ferrules in the
plate. Slack in shielding or wire can be removed by grasping the lead in one hand and sliding the other
hand firmly along the lead towards the magneto cover.
To replace contact springs, insulating sleeves, compression spring or elbows, proceed as follows:
1. Using a Bendix 11-7073 needle or a mechanical pencil with the lead retracted, hook the end of the
contact spring as shown in Figure 23.
2. Using the needle or pencil, unscrew the spring.
3. Slide insulating sleeve and spring retainer assembly off end of lead assembly.
4. Replace defective component and reassemble as follows:
a. Fabricate a tool as shown in Figure 24 for installing the insulating sleeves over cable terminals.
b. Slide elbow assembly over lead and attach nut finger tight to ferrule.
c. Push the fabricated tool through insulating sleeve and spring retainer assembly as shown in
Figure 25. Screw the cable terminal into the tool.
d. Work insulating sleeve and spring retainer assembly into position over the cable and unscrew the
tool. Install contact spring on cable terminal.
– NOTE –
It may be necessary to lubricate the cable and insulating sleeve
with a thin film of DC-200 (200,000 centistokes) or commer-
cial grade alcohol to facilitate assembly.
5. To replace one of the lead assemblies, proceed as follows:
a. Remove clamps and brackets from defective lead assembly. Cut cable ties from assembly and
discard .
b. Cut the eyelet from the lead and remove grommet.
c. Grip the ferrule of the lead with a pair of vise grip or water pump pliers and with a twist-pull
action remove the ferrule from the cover and discard ferrule. Pull lead from cover.
d. Thread pre-stripped end of replacement lead through cover.
– NOTE –
Replacement leads are available from Bendix in lengths of 17
thru 74 inches in 3 inch increments. Use nearest next longer
length to replace defective lead.
e. Scrape blue coating being careful not to cut braid for .50 of an inch from end of lead.
– CAUTION –
New ferrules must be used and inserted under the braid exactly
as stated in Step F.
f.
Push back braid and thread a new ferrule over wire and under braid until braid just covers knurl-
PIPER AIRCRAFT
PA-32R-301/301T
MAINTENANCE MANUAL
74-20-00
Page 74-22
Reissued: July 1, 1993
4B24
Summary of Contents for PA-32R-301T SARATOGA S
