background image

Page 6

For technical questions, please call 1-800-444-3353.

Item 69887 

        

Maintenance and Servicing

Procedures not specifically explained in this manual  

must be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM STAND FAILURE: 

Do not use damaged equipment.  Make sure the stand is stable. If any unsafe 

conditions are found, take it to a qualified technician for service or repair.

1. 

BEFORE EACH USE,

 inspect the 

general condition of the Stand.  Check 

it for cracks, bends in the metal, signs 

of unusual wear or any other condition 

that may affect its safe operation.  

If any are found, do not use the Stand.

2.  Keep Engine Stand clean and 

free of dirt or grease.

3.  Before each use, check that 

hardware is securely fastened.

4.  Check that the Casters are 

clean and turn properly.

5. 

AFTER USE,

 clean external surfaces 

of the stand with a clean, moist cloth.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY 

DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER 

OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE 

BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR 

THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE 

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS 

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, 

AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF 

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, 

OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Note:

 Some parts are listed and shown for illustration purposes only, 

and are not available individually as replacement parts.

Record Serial Number Here: 
Note: If product has no serial number, record month and year of purchase instead.

Summary of Contents for 69887









Reviews: