background image

Clean Pole Installation and User’s Guide (OM720-02)     5

Damage Requiring Service

Unplug the unit from the wall outlet and call Planar Customer Service when any of the
following conditions occur:

A.

 

When the power cord is damaged or frayed.

B.

 

If the unit does not operate normally by following the operating instructions.

C.

 

It the unit exhibits a distinct change in performance.

Terms and Symbols

Various terms and symbols are used in this manual and on the equipment. These terms and
symbols alert you to possible hazards or other conditions of which you may need to be aware.
These terms and conditions are shown in the following tables:

Terms and Symbols in the Manual

CAUTION

CAUTION statements involve conditions or practices that could damage

the equipment or other property.

W A R N I N G

WARNING statements involve conditions or practices that could result in

injury or loss of life.

Terms and Symbols on the Equipment

CAUTION

CAUTION shows an injury hazard not immediately accessible as one reads

the marking, or a hazard to property including the equipment itself.

WARNING

DANGER

WARNING or DANGER shows an immediately accessible injury hazard.

!

ATTENTION -- Refer to manual

Class II Equipment

Summary of Contents for Clean Pole

























Reviews: