background image

 

   

EL640.480-AF1 VGA Operations Manual (020-0349-00A) 

13 

Description of Warranty

 

Seller warrants that the Goods will conform to published specifications and be free from defects in 
material for 12 months from delivery.  To the extent that Goods incorporate third-party-owned 
software, Seller shall pass on Seller's licensor's warranty to Buyer subject to the terms and conditions 
of Seller's license.   

Warranty repairs shall be warranted for the remainder of the original warranty period.  Buyer shall 
report defect claims in writing to Seller immediately upon discovery, and in any event, within the 
warranty period.  Buyer must return Goods to Seller within 30 days of Seller’s receipt of a warranty 
claim notice and only after receiving Seller’s Return Goods Authorization.  Seller shall, at its sole 
option, repair or replace the Goods.   

If Goods were repaired, altered or modified by persons other than Seller, this warranty is void.  
Conditions resulting from normal wear and tear and Buyer's failure to properly store, install, operate, 
handle or maintain the Goods are not within this warranty.  Repair or replacement of Goods is 
Seller’s sole obligation and Buyer's exclusive remedy for all claims of defects.  If that remedy is 
adjudicated insufficient, Seller shall refund Buyer's paid price for the Goods and have no other 
liability to Buyer.   

All warranty repairs must be performed at Seller’s authorized service center using parts approved by 
Seller.  Buyer shall pay costs of sending Goods to Seller on a warranty claim and Seller shall pay costs 
of returning Goods to Buyer.  The turnaround time on repairs will usually be 30 working days or less.  
Seller accepts no added liability for additional days for repair or replacement.   

If Seller offers technical support relating to the Goods, such support shall neither modify the 
warranty nor create an obligation of Seller.  Buyer is not relying on Seller’s skill or judgment to select 
Goods for Buyer’s purposes.  Seller’s software, if included with Goods, is sold as is, and this warranty 
is inapplicable to such software.   

SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED 
TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 

Ordering Information 

Product Part 

Number 

Description 

EL640.480-AF1 

996-0270-00 

6.4" diagonal, 640x480 VGA display  
-5 to 55

°

C operating temperature 

EL640.480-AF1 AG 

996-0270-01 

EL640.480-AF1 with anti-glare coating 

Design and specifications are subject to change without notice. 

Planar Systems continues to provide optional, and in many cases custom, features to address 
the specific customer requirements. Consult Planar Sales for pricing, lead time and minimum 
quantity requirements. 

Summary of Contents for EL640.480-AF1


















Reviews: